 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| FDC37C78 Floppy Disk Controller FEATURES * * * 3.3/5 Volt Operation Intelligent Auto Power Management 2.88MB FDC37C78 Floppy Disk Controller Licensed CMOS 765B Floppy Disk Controller Software and Register Compatible with SMSC's Proprietary 82077AA Compatible Core Supports Two Floppy Drives Directly Supports Vertical Recording Format 16 Byte Data FIFO 100% IBM Compatibility DMA Enable Logic Data Rate and Drive Control Registers Swap Drives A and B Non-Burst Mode DMA Option Detects All Overrun and Underrun Conditions Sophisticated Power Control Circuitry (PCC) Including Multiple Powerdown Modes for Reduced Power Consumption Enhanced Digital Data Separator - 2 Mbps (Only Available When VCC = 5V), 1 Mbps, 500 Kbps, 300 Kbps, 250 Kbps Data Rates - Programmable Precompensation Modes 48 pin TQFP Package - * * TABLE OF CONTENTS FEATURES...............................................................................................................................................1 GENERAL DESCRIPTION .......................................................................................................................3 PIN CONFIGURATION.............................................................................................................................4 DESCRIPTION OF PIN FUNCTIONS ......................................................................................................6 FUNCTIONAL DESCRIPTION ...............................................................................................................10 FDC37C78 REGISTERS ..................................................................................................................10 HOST PROCESSOR INTERFACE ..................................................................................................10 FLOPPY DISK CONTROLLER .........................................................................................................11 FLOPPY DISK CONTROLLER INTERNAL REGISTERS.................................................................11 COMMAND SET/DESCRIPTIONS .........................................................................................................29 INSTRUCTION SET ...............................................................................................................................32 AUTO POWER MANAGEMENT.............................................................................................................58 CONFIGURATION..................................................................................................................................62 OPERATIONAL DESCRIPTION.............................................................................................................71 MAXIMUM GUARANTEED RATINGS ..............................................................................................71 DC ELECTRICAL CHARACTERISTICS ...........................................................................................71 TIMING DIAGRAMS ...............................................................................................................................75 2 GENERAL DESCRIPTION The SMSC FDC37C78 Floppy Disk Controller utilizes SMSC's proven SuperCell technology for increased product reliability and functionality. The FDC37C78 optimized for motherboard applications. The FDC37C78 supports both 1 Mbps and 2 Mbps data rates and vertical vertical recording operation at 1 Mbps Data Rate. The FDC37C78 incorporates SMSC's true CMOS 765B floppy disk controller, advanced digital data separator, 16 byte data FIFO, on-chip 12 mA bus drivers and two floppy direct drive support. The true CMOS 765B core provides 100% compatibility with IBM PC/XT and PC/AT architectures in addition to providing data overflow and underflow protection. The SMSC advanced digital data separator incorporates SMSC's patented data separator technology, allowing for ease of testing and use. The FDC37C78 incorporates sophisticated power control circuitry (PCC). The PCC supports multiple low power down modes. The FDC37C78 Floppy Disk Controller incorporates Software Configurable Logic (SCL) for ease of use. Use of the SCL feature allows programmable system configuration of key functions of FDC The FDC37C78 does not require any external filter components, and is, therefore easy to use and offers lower system cost and reduced board area. The FDC37C78 is software and register compatible with SMSC's proprietary 82077AA core. 3 PIN CONFIGURATION RESET 38 nIOW nIOR DRQ nCS 48 nDACK D0 D1 D2 D3 VSS VCC D4 D5 D6 D7 VCC 1 2 3 4 5 6 7 8 9 10 11 12 13 47 46 45 44 43 42 41 40 39 37 36 35 34 33 32 nMTR0 nDS1/PD nMTR1/IDLE nDIR VCC nSTEP VSS nHDSEL nWGATE nWDATA MEDIA_ID1 MEDIA_ID0 nDS0 31 30 29 28 27 26 25 24 DENSEL VSS A0 A1 A2 X1 21 FDC37C78 14 15 16 17 18 19 20 X2 22 DRVDEN0 23 nDSKCHG nWRTPRT 4 DRVDEN1 nINDEX VCC VSS nRDATA nTRK0 IRQ TC FDC37C78 PIN OUT FDC37C78 48 Pin FDC PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Note: "n" denotes active low signal. NAME nDACK D0 D1 D2 D3 VSS VCC D4 D5 D6 D7 VCC IRQ TC nTRK0 nINDEX nWRTPRT VSS VCC nDSKCHG nRDATA DRVDEN0 DRVDEN1 DENSEL PIN # 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 NAME MEDIA_ID0 MEDIA_ID1 nWDATA nWGATE nHDSEL VSS nSTEP VCC nDIR nMTR1/IDLE nDS1/PD nMTR0 nDS0 RESET X2 X1 VSS A2 A1 A0 nCS nIOR nIOW DRQ 5 DESCRIPTION OF PIN FUNCTIONS DESCRIPTION OF PIN FUNCTIONS PIN NO. 2-5, 8-11 46 47 44-42 I/O Read I/O Write I/O Address nIOR nIOW A0-A2 I I I NAME Data Bus 0-7 SYMBOL D0-D7 BUFFER TYPE I/O12 DESCRIPTION The data bus connection used by the host microprocessor to transmit data to and from the chip. These pins are in a high-impedance state when not in the output mode. This active low signal is issued by the host microprocessor to indicate a read operation. This active low signal is issued by the host microprocessor to indicate a write operation. These host address bits determine the I/O address to be accessed during nIOR and nIOW cycles. These bits are latched internally by the leading edge of nIOR and nIOW. This active high output is the DMA request for byte transfers of data between the host and the chip. This signal is cleared on the last byte of the data transfer by the nDACK signal going low (or by nIOR going low if nDACK was already low as in demand mode). An active low input acknowledging the request for a DMA transfer of data between the host and the chip. This input enables the DMA read or write internally. This signal indicates to the chip that DMA data transfer is complete. TC is only accepted when nDACK is low. TC is active high. The interrupt request from the logical device is output on the IRQ signal. Refer to the configuration registers for more information. When enabled, this active low pin serves as an input for an external decoder circuit which is used to qualify address lines above A2. HOST PROCESSOR INTERFACE 48 DMA Request DRQ O12 1 n DMA Acknowledge nDACK I 14 Terminal Count TC I 13 Interrupt Request IRQ O12 45 Chip Select Input nCS I 6 DESCRIPTION OF PIN FUNCTIONS PIN NO. 38 NAME Reset SYMBOL RESET BUFFER TYPE IS DESCRIPTION This active high signal resets the chip and must be valid for 500 ns minimum. The effect on the internal registers is described in the appropriate section. The configuration registers are not affected by this reset. Raw serial bit stream from the disk drive, low active. Each falling edge represents a flux transition of the encoded data. This active low high current driver provides the encoded data to the disk drive. Each falling edge causes a flux transition on the media. This high current output selects the floppy disk side for reading or writing. A logic "1" on this pin means side 0 will be accessed, while a logic "0" means side 1 will be accessed. This high current low active output determines the direction of the head movement. A logic "1" on this pin means outward motion, while a logic "0" means inward motion. This active low high current driver issues a low pulse for each track-to-track movement of the head. This input senses that the drive door is open or that the diskette has possibly been changed since the last drive selection. This input is inverted and read via bit 7 of I/O address 3F7H. Indicates the drive and media selected. Refer to configuration registers CR03, CR0B, CR1F. Indicates whether a low (250/300 Kb/s) or high (500 Kb/s) data rate has been selected. This is determined by the IDENT bit in Configuration Register 3. FLOPPY DISK INTERFACE 21 Read Disk Data nRDATA IS 27 Write Data Head Select nWDATA OD20 29 nHDSEL OD20 33 Direction Control Step Pulse nDIR OD20 31 nSTEP OD20 20 Disk Change nDSKCHG IS 22, 23 24 DRVDEN 0, DRVDEN 1 Density Select DRVDEN0, DRVDEN1 DENSEL OD20 OD20 7 DESCRIPTION OF PIN FUNCTIONS PIN NO. 25, 26 28 NAME Media ID0, Media ID1 Write Gate SYMBOL MEDIA_ID0, MEDIA_ID1 nWGATE OD20 BUFFER TYPE I DESCRIPTION In Floppy Enhanced Mode 2 - These bits are the Media ID 0,1 inputs. The value of these bits can be read as bits 6 and 7 of the Floppy Tape Register. This active low high current driver allows current to flow through the write head. It becomes active just prior to writing to the diskette. This active low Schmitt Trigger input senses from the disk drive that the head is positioned over the outermost track. This active low Schmitt Trigger input senses from the disk drive that the head is positioned over the beginning of a track, as marked by an index hole. This active low Schmitt Trigger input senses from the disk drive that a disk is write protected. Any write command is ignored. This active low open drain output selects motor drive 0. This active low open drain output selects drive 0. This active low open drain output select motor drive 0. This pin indicates that the part is in the IDLE state and can be powered down. Whenever the part is in this state, IDLE pin is active high. If the part is powered down by the Auto Powerdown Mode, IDLE pin is set high and if the part is powered down by setting the DSR POWERDOWN bit (direct), IDLE pin is set low. This active low open drain output selects drive 0. This pin is active high whenever the part is in powerdown state, either via DSR POWERDOWN bit (direct) or via the Auto Powerdown Mode. This pin can be used to disable an external oscillator's output. 15 Track 0 nTRK0 IS 16 Index nINDEX IS 17 nWrite Protected nWRTPRT IS 36 37 34 nMotor On 0 nDrive Select 0 nMotor On 1 Idle nMTR0 nDS0 nMTR1 IDLE OD20 OD20 OD20 OD20 35 nDrive Select 1 Powerdown nDS1 PD OD20 OD20 8 DESCRIPTION OF PIN FUNCTIONS PIN NO. 40 NAME CLOCK 1 SYMBOL X1 BUFFER TYPE MISCELLANEOUS ICLK The external connection for a parallel resonant 24 MHz crystal. A CMOS compatible oscillator is required if crystal is not used. 24 MHz crystal. If an external clock is used, this pin should not be connected. This pin should not be used to drive any other drivers. Positive Supply Voltage. Ground Supply. DESCRIPTION 39 CLOCK 2 X2 OCLK 7, 12, 19, Power 32 6, 18, 30, Ground 41 VCC GND BUFFER TYPE DESCRIPTIONS Note: These values are for 3.3V operation. See Operational Description for 3.3V/5V values. BUFFER TYPE I/O12 O12 OD20 OCLK ICLK I IS DESCRIPTION Input/output. 12 mA sink; 6 mA source Output. 12 mA sink; 6 mA source Open drain. 20 mA sink Output to external crystal Input to Crystal Oscillator Circuit (CMOS levels) Input TTL compatible. Input with Schmitt Trigger 9 FUNCTIONAL DESCRIPTION FDC37C78 REGISTERS The address map, shown below in Table 1, shows the addresses of the different blocks of the FDC37C78 immediately after power up. Some addresses are used to access more than one register. HOST PROCESSOR INTERFACE The host processor communicates with the FDC37C78 through a series of read/write registers. The port addresses for these registers are shown in Table 1. Register access is accomplished through programmed I/O or DMA transfers. All registers are 8 bits wide. ADDRESS +0, +1 Base +0,1 Base +[2:5, 7] Table 1 - FDC37C78 Block Addresses BLOCK NAME Configuration Floppy Disk Floppy Disk NOTES Write only; Note 1, 2 Read only; Disabled at power up; Note 2 Disabled at power up; Note 2 Note 1: Configuration registers can only be modified in configuration mode, refer to the configuration register description for more information. Access to status registers A and B of the floppy disk is disabled in configuration mode. Note 2: The fdc must be enabled in the configuration registers before accessing the registers. 10 FLOPPY DISK CONTROLLER The Floppy Disk Controller (FDC) provides the interface between a host microprocessor and the floppy disk drives. The FDC integrates the functions of the Formatter/Controller, Digital Data Separator, Write Precompensation and Data Rate Selection logic for an IBM XT/AT compatible FDC. The true CMOS 765B core guarantees 100% IBM PC XT/AT compatibility in addition to providing data overflow and underflow protection. The FDC37C78 is compatible to the 82077AA using SMSC's proprietary floppy disk controller core. FLOPPY DISK REGISTERS CONTROLLER INTERNAL The Floppy Disk Controller contains eight internal registers which facilitate the interfacing between the host microprocessor and the disk drive. Table 2 shows the addresses required to access these registers. Registers other than the ones shown are not supported. The rest of the FDC description assumes the Base I/O Address is 3F0. Table 2 - Status, Data and Control Registers BASE I/O ADDRESS +0 +1 +2 +3 +4 +4 +5 +6 +7 +7 REGISTER Reserved Reserved Digital Output Register Tape Drive Register Main Status Register Data Rate Select Register Data (FIFO) Reserved Digital Input Register Configuration Control Register R/W R/W R W R/W R W DOR TSR MSR DSR FIFO DIR CCR 11 DIGITAL OUTPUT REGISTER (DOR) Address 3F2 READ/WRITE The DOR controls the drive select and motor enables of the disk interface outputs. It also 7 MOT EN3 0 6 MOT EN2 0 5 MOT EN1 0 4 MOT EN0 0 contains the enable for the DMA logic and contains a software reset bit. The contents of the DOR are unaffected by a software reset. The DOR can be written to at any time. RESET COND. 3 2 1 0 DMAEN nRESET DRIVE DRIVE SEL1 SEL0 0 0 0 0 BIT 0 and 1 DRIVE SELECT These two bit a are binary encoded for the four drive selects DS0-DS3, thereby allowing only one drive to be selected at one time. BIT 2 nRESET A logic "0" written to this bit resets the Floppy disk controller. This reset will remain active until a logic "1" is written to this bit. This software reset does not affect the DSR and CCR registers, nor does it affect the other bits of the DOR register. The minimum reset duration required is 100ns, therefore toggling this bit by consecutive writes to this register is a valid method of issuing a software reset. BIT 3 DMAEN Writing this bit to logic "1" will enable the DRQ, nDACK, TC and IRQ outputs. This bit being a logic "0" will disable the nDACK and TC inputs, and hold the DRQ and IRQ outputs in a high impedance state. This bit is a logic "0" after a reset and in these modes. BIT 4 MOTOR ENABLE 0 This bit controls the MTR0 disk interface output. A logic "1" in this bit will cause the output pin to go active. BIT 5 MOTOR ENABLE 1 This bit controls the MTR1 disk interface output. A logic "1" in this bit will cause the output pin to go active. BIT 6 MOTOR ENABLE 2 This bit controls the MTR2 disk interface output. A logic "1" in this bit will cause the output pin to go active. BIT 7 MOTOR ENABLE 3 This bit controls the MTR3 disk interface output. A logic "1" in this bit causes the output to go active. Table 3 - Drive Activation Values DRIVE 0 1 2 3 DOR VALUE 1CH 2DH 4EH 8FH 12 TAPE DRIVE REGISTER (TDR) Address 3F3 READ/WRITE This register is included for 82077 software compatability. The robust digital data separator used in the FDC37C78 does not require its characteristics modified for tape support. The contents of this register are not used internal to the device. The TDR is unaffected by a software reset. Bits 2-7 are tri-stated when read in this mode. Table 4- Tape Select Bits TAPE SEL1 0 0 1 1 TAPE SEL2 0 1 0 1 DRIVE SELECTED None 1 2 3 Table 5 - Internal 4 Drive Decode - Normal DIGITAL OUTPUT REGISTER Bit 7 X X X 1 0 Bit 6 X X 1 X 0 Bit 5 X 1 X X 0 Bit 4 1 X X X 0 Bit1 0 0 1 1 X Bit 0 0 1 0 1 X DRIVE SELECT OUTPUTS (ACTIVE LOW) nDS3 1 1 1 0 1 nDS2 1 1 0 1 1 nDS1 1 0 1 1 1 nDS0 0 1 1 1 1 nMTR3 nBIT 7 nBIT 7 nBIT 7 nBIT 7 nBIT 7 MOTOR ON OUTPUTS (ACTIVE LOW) nMTR2 nBIT 6 nBIT 6 nBIT 6 nBIT 6 nBIT 6 nMTR1 nBIT 5 nBIT 5 nBIT 5 nBIT 5 nBIT 5 nMTR0 nBIT 4 nBIT 4 nBIT 4 nBIT 4 nBIT 4 Table 6 - Internal 4 Drive Decode - Drives 0 and 1 Swapped DIGITAL OUTPUT REGISTER Bit 7 X X X 1 0 Bit 6 X X 1 X 0 Bit 5 X 1 X X 0 Bit 4 1 X X X 0 Bit1 0 0 1 1 X Bit 0 0 1 0 1 X DRIVE SELECT OUTPUTS (ACTIVE LOW) nDS3 1 1 1 0 1 nDS2 1 1 0 1 1 nDS1 0 1 1 1 1 nDS0 1 0 1 1 1 nMTR3 nBIT 7 nBIT 7 nBIT 7 nBIT 7 nBIT 7 MOTOR ON OUTPUTS (ACTIVE LOW) nMTR2 nBIT 6 nBIT 6 nBIT 6 nBIT 6 nBIT 6 nMTR1 nBIT 4 nBIT 4 nBIT 4 nBIT 4 nBIT 4 nMTR0 nBIT 5 nBIT 5 nBIT 5 nBIT 5 nBIT 5 13 Table 7 - External 2 to 4 Drive Decode - Normal DIGITAL OUTPUT REGISTER Bit 7 X X X 1 X X X 0 Bit 6 X X 1 X X X 0 X Bit 5 X 1 X X X 0 X X Bit 4 1 X X X 0 X X X Bit1 0 0 1 1 0 0 1 1 Bit 0 0 1 0 1 0 1 0 1 DRIVE SELECT OUTPUTS (ACTIVE LOW) nDS1 0 0 1 1 0 0 1 1 nDS0 0 1 0 1 0 1 0 1 MOTOR ON OUTPUTS (ACTIVE LOW) nMTR1 1 1 1 1 1 1 1 1 nMTR0 0 0 0 0 1 1 1 1 Table 8 - External 2 to 4 Drive Decode - Drives 0 and 1 Swapped DIGITAL OUTPUT REGISTER Bit 7 X X X 1 X X X 0 Bit 6 X X 1 X X X 0 X Bit 5 X 1 X X X 0 X X Bit 4 1 X X X 0 X X X Bit1 0 0 1 1 0 0 1 1 Bit 0 0 1 0 1 0 1 0 1 DRIVE SELECT OUTPUTS (ACTIVE LOW) nDS1 0 0 1 1 0 0 1 1 nDS0 1 0 0 1 1 0 0 1 MOTOR ON OUTPUTS (ACTIVE LOW) nMTR1 1 1 1 1 1 1 1 1 nMTR0 0 0 0 0 1 1 1 1 14 Normal Floppy Mode Normal mode. Register 3F3 contains only bits 0 and 1. When this register is read, bits 2 - 7 are a high impedance. DB7 REG 3F3 Tri-state DB6 Tri-state DB5 Tri-state DB4 Tri-state DB3 Tri-state DB2 Tri-state DB1 tape sel1 DB0 tape sel0 Enhanced Floppy Mode 2 (OS2) Register 3F3 for Enhanced Floppy Mode 2 operation. DB7 REG 3F3 Media ID1 DB6 Media ID0 DB5 DB4 DB3 DB2 DB1 tape sel1 DB0 tape sel0 Drive Type ID Floppy Boot Drive For this mode, DRATE0 and DRATE1 pins are inputs, and these inputs are gated into bits 6 and 7 of the 3F3 register. These two bits are not affected by a hard or soft reset. BIT 7 Media ID 1; Read Only (See Table 9a) BIT 6 Media ID 0; Read Only (See Table 9b) BITS 5 and 4 Drive Type ID - These Bits reflect two of the bits of configuration register 6; which two bits depends on the last drive selected in the Digital Output Register (3F2). (See Table 11) BITS 3 and 2 Floppy Boot Drive - These bits reflect the value of configuration register 7 bits 1, 0. Bit 3 = CR7 Bit DB1. Bit 2 = CR7 Bit DB0. Bits 1 and 0 - Tape Drive Select (READ/WRITE). Same as in Normal and Enhanced Floppy Mode. 1. Table 9a Media ID1 Bit 7 CR7-DB3=0 CR7-DB3=1 0 1 1 0 Table 9b Media ID0 Bit 6 CR7-DB2=0 CR7-DB2=1 0 1 1 0 Pin 26 0 1 Pin 25 0 1 Table 9c - Drive Type ID Digital Output Register Register 3F3 - Drive Type ID Bit 1 0 0 1 1 Bit 0 0 1 0 1 Bit 5 CR6 - Bit 1 CR6 - Bit 3 CR6 - Bit 5 CR6 - Bit 7 Bit 4 CR6 - Bit 0 CR6 - Bit 2 CR6 - Bit 4 CR6 - Bit 6 15 DATA RATE SELECT REGISTER (DSR) Address 3F4 WRITE ONLY This register is write only. It is used to program the data rate, amount of write precompensation, power down status, and software reset. The data rate is programmed using the Configuration Control Register (CCR) 7 6 S/W POWER RESET DOWN 0 0 5 0 0 not the DSR, for PC/AT and Microchannel applications. Other applications can set the data rate in the DSR. The data rate of the floppy controller is the most recent write of either the DSR or CCR. The DSR is unaffected by a software reset. A hardware reset will set the DSR to 02H, which corresponds to the default precompensation setting and 250 kbps. 3 PRECOMP1 0 2 1 0 PREDRATE DRATE COMP0 SEL1 SEL0 0 1 0 RESET COND. 4 PRECOMP2 0 BIT 0 and 1 DATA RATE SELECT These bits control the data rate of the floppy controller. See Table 13 for the settings corresponding to the individual data rates. The data rate select bits are unaffected by a software reset, and are set to 250 kbps after a hardware reset. BIT 2 through 4 PRECOMPENSATION SELECT These three bits select the value of write precompensation that will be applied to the WDATA output signal. Table 12 shows the precompensation values for the combination of these bits settings. Track 0 is the default starting track number to start precompensation. this starting track number can be changed by the configure command. BIT 5 UNDEFINED Should be written as a logic "0". BIT 6 LOW POWER A logic "1" written to this bit will put the floppy controller into Manual Low Power mode. The floppy controller clock and data separator circuits will be turned off. The controller will come out of manual low power mode after a software reset or access to the Data Register or Main Status Register. BIT 7 SOFTWARE RESET This active high bit has the same function as the DOR RESET (DOR bit 2) except that this bit is self clearing. Table 10 - Precompensation Delays PRECOMP 432 111 001 010 011 100 101 110 000 PRECOMPENSATION DELAY 0.00 ns-DISABLED 41.67 ns 83.34 ns 125.00 ns 166.67 ns 208.33 ns 250.00 ns Default (See Table 14) 16 DRIVE RATE DRT1 0 0 0 0 0 0 0 0 1 1 1 1 DRT0 0 0 0 0 1 1 1 1 0 0 0 0 DATA RATE SEL1 1 0 0 1 1 0 0 1 1 0 0 1 SEL0 1 0 1 0 1 0 1 0 1 0 1 0 Table 11 - Data Rates DATA RATE MFM 1Meg 500 300 250 1Meg 500 500 250 1Meg 500 2Meg 250 FM --250 150 125 --250 250 125 --250 --125 1 1 0 0 1 1 0 0 1 1 0 0 DENSEL (1) IDENT=0 0 0 1 1 0 0 1 1 0 0 1 1 DRATE (2) 1 1 0 0 1 1 0 0 1 1 0 0 1 2 1 0 1 0 1 0 1 0 1 0 1 0 IDENT=1 Drive Rate Table (Recommended) 00 = 360K, 1.2M, 720K, 1.44M and 2.88M Vertical Format 01 = 3-Mode Drive 10 = 2 Meg Tape Note 1: This is for DENSEL in normal mode. Note 2: This is for DRATE0, DRATE1 when Drive Opt are 00. Table 12 - Default Precompensation Delays DATA RATE 2 Mbps 1 Mbps 500 Kbps 300 Kbps 250 Kbps PRECOMPENSATION DELAYS 20.8 ns 41.67 ns 125 ns 125 ns 125 ns *The 2 Mbps data rate is only available if VCC = 5V. 17 MAIN STATUS REGISTER Address 3F4 READ ONLY The Main Status Register is a read-only register and indicates the status of the disk controller. The Main Status Register can be read at any 7 RQM 6 DIO 5 NON DMA 4 CMD BUSY time. The MSR indicates when the disk controller is ready to receive data via the Data Register. It should be read before each byte transferring to or from the data register except in DMA mode. NO delay is required when reading the MSR after a data transfer. 3 DRV3 BUSY 2 DRV2 BUSY 1 DRV1 BUSY 0 DRV0 BUSY BIT 0 - 3 DRVx BUSY These bits are set to 1s when a drive is in the seek portion of a command, including implied and overlapped seeks and recalibrates. BIT 4 COMMAND BUSY This bit is set to a 1 when a command is in progress. This bit will go active after the command byte has been accepted and goes inactive at the end of the results phase. If there is no result phase (Seek, Recalibrate commands), this bit is returned to a 0 after the last command byte. BIT 5 NON-DMA This mode is selected in the SPECIFY command and will be set to a 1 during the execution phase of a command. This is for polled data transfers and helps differentiate between the data transfer phase and the reading of result bytes. BIT 6 DIO Indicates the direction of a data transfer once a RQM is set. A 1 indicates a read and a 0 indicates a write is required. BIT 7 RQM Indicates that the host can transfer data if set to a 1. No access is permitted if set to a 0. 18 DATA REGISTER (FIFO) Address 3F5 READ/WRITE All command parameter information, disk data and result status are transferred between the host processor and the floppy disk controller through the Data Register. Data transfers are governed by the RQM and DIO bits in the Main Status Register. The Data Register defaults to FIFO disabled mode after any form of reset. This maintains PC/AT hardware compatibility. The default values can be changed through the Configure command (enable full FIFO operation with threshold control). The advantage of the FIFO is that it allows the system a larger DMA latency without causing a disk error. Table 15 gives several examples of the delays with a FIFO. The data is based upon the following formula: Threshold # x 1 DATA RATE x8 - 1.5 s = DELAY At the start of a command, the FIFO action is always disabled and command parameters must be sent based upon the RQM and DIO bit settings. As the command execution phase is entered, the FIFO is cleared of any data to ensure that invalid data is not transferred. An overrun or underrun will terminate the current command and the transfer of data. Disk writes will complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to remove the remaining data so that the result phase may be entered. Table 13- FIFO Service Delay MAXIMUM DELAY TO SERVICING AT FIFO THRESHOLD EXAMPLES 2 Mbps* DATA RATE 1 byte 2 bytes 8 bytes 15 bytes FIFO THRESHOLD EXAMPLES 1 byte 2 bytes 8 bytes 15 bytes FIFO THRESHOLD EXAMPLES 1 byte 2 bytes 8 bytes 15 bytes 1 x 4 s - 1.5 s = 2.5 s 2 x 4 s - 1.5 s = 6.5 s 8 x 4 s - 1.5 s = 30.5 s 15 x 4 s - 1.5 s = 58.5 s MAXIMUM DELAY TO SERVICING AT 1 Mbps DATA RATE 1 x 8 s - 1.5 s = 6.5 s 2 x 8 s - 1.5 s = 14.5 s 8 x 8 s - 1.5 s = 62.5 s 15 x 8 s - 1.5 s = 118.5 s MAXIMUM DELAY TO SERVICING AT 500 Kbps DATA RATE 1 x 16 s - 1.5 s = 14.5 s 2 x 16 s - 1.5 s = 30.5 s 8 x 16 s - 1.5 s = 126.5 s 15 x 16 s - 1.5 s = 238.5 s *The 2 Mbps data rate is only available if VCC = 5V. 19 DIGITAL INPUT REGISTER (DIR) Address 3F7 READ ONLY This register is read-only. 7 DSK CHG N/A 6 5 4 3 2 1 0 RESET COND. N/A N/A N/A N/A N/A N/A N/A BIT 0 - 6 UNDEFINED The data bus outputs D0 - 6 will remain in a high impedance state during a read of this register. BIT 7 DSKCHG This bit monitors the pin of the same name and reflects the opposite value seen on the disk cable. 20 CONFIGURATION CONTROL REGISTER (CCR) Address 3F7 WRITE ONLY 7 6 5 4 3 2 1 0 DRATE DRATE SEL1 SEL0 1 0 RESET COND. N/A N/A N/A N/A N/A N/A BIT 0 and 1 DATA RATE SELECT 0 and 1 These bits determine the data rate of the floppy controller. See Table 13 for the appropriate values. BIT 2 - 7 RESERVED Should be set to a logical "0" by the DOR and the DSR resets. 21 STATUS REGISTER ENCODING During the Result Phase of certain commands, the Data Register contains data bytes that give the status of the command just executed. Table 14 - Status Register 0 NAME DESCRIPTION Interrupt Code 00 - Normal termination of command. The specified command was properly executed and completed without error. 01 - Abnormal termination of command. Command execution was started, but was not successfully completed. 10 - Invalid command. The requested command could not be executed. 11 - Abnormal termination caused by Polling. Seek End The FDC completed a Seek, Relative Seek or Recalibrate command (used during a Sense Interrupt Command). The TRK0 pin failed to become a "1" after: 1. 80 step pulses in the Recalibrate command. 2. The Relative Seek command caused the FDC to step outward beyond Track 0. Unused. This bit is always "0". H DS1,0 Head Address The current head address. Drive Select The current selected drive. BIT NO. 7,6 SYMBOL IC 5 SE 4 EC Equipment Check 3 2 1,0 22 BIT NO. 7 SYMBOL EN Table 15 - Status Register 1 NAME DESCRIPTION End of Cylinder The FDC tried to access a sector beyond the final sector of the track (255D*). Will be set if TC is not issued after Read or Write Data command. Unused. This bit is always "0". The FDC detected a CRC error in either the ID field or the data field of a sector. Becomes set if the FDC does not receive CPU or DMA service within the required time interval, resulting in data overrun or underrun. Unused. This bit is always "0". Any one of the following: 1. Read Data, Read Deleted Data command the FDC did not find the specified sector. 2. Read ID command - the FDC cannot read the ID field without an error. 3. Read A Track command - the FDC cannot find the proper sector sequence. WP pin became a "1" while the FDC is executing a Write Data, Write Deleted Data, or Format A Track command. Any one of the following: 1. The FDC did not detect an ID address mark at the specified track after encountering the index pulse from the IDX pin twice. 2. The FDC cannot detect a data address mark or a deleted data address mark on the specified track. 6 5 4 DE OR Data Error Overrun/ Underrun 3 2 ND No Data 1 0 NW MA Not Writable Missing Address Mark * D= Decimal 23 BIT NO. 7 6 SYMBOL CM Table 16 - Status Register 2 NAME DESCRIPTION Unused. This bit is always "0". Control Mark Any one of the following: 1. Read Data command - the FDC encountered a deleted data address mark. 2. Read Deleted Data command - the FDC encountered a data address mark. The FDC detected a CRC error in the data field. The track address from the sector ID field is different from the track address maintained inside the FDC. Unused. This bit is always "0". Unused. This bit is always "0". 5 4 3 2 1 DD WC Data Error in Data Field Wrong Cylinder BC Bad Cylinder The track address from the sector ID field is different from the track address maintained inside the FDC and is equal to FF hex, which indicates a bad track with a hard error according to the IBM soft-sectored format. The FDC cannot detect a data address mark or a deleted data address mark. 0 MD Missing Data Address Mark 24 BIT NO. 7 6 5 4 3 2 1,0 SYMBOL WP Table 17 - Status Register 3 NAME DESCRIPTION Unused. This bit is always "0". Write Protected Track 0 Indicates the status of the WP pin. Unused. This bit is always "1". T0 HD DS1,0 Indicates the status of the TRK0 pin. Unused. This bit is always "1". Head Address Indicates the status of the HDSEL pin. Drive Select Indicates the status of the DS1, DS0 pins. RESET There are three sources of system reset on the FDC: the RESET pin of the FDC37C78, a reset generated via a bit in the DOR, and a reset generated via a bit in the DSR. At power on, a Power On Reset initializes the FDC. All resets take the FDC out of the power down state. All operations are terminated upon a RESET, and the FDC enters an idle state. A reset while a disk write is in progress will corrupt the data and CRC. On exiting the reset state, various internal registers are cleared, including the Configure command information, and the FDC waits for a new command. Drive polling will start unless disabled by a new Configure command. RESET Pin (Hardware Reset) The RESET pin is a global reset and clears all registers except those programmed by the Specify command. The DOR reset bit is enabled and must be cleared by the host to exit the reset state. DOR Reset vs. DSR Reset (Software Reset) These two resets are functionally the same. Both will reset the FDC core, which affects drive status information and the FIFO circuits. The DSR reset clears itself automatically while the DOR reset requires the host to manually clear it. DOR reset has precedence over the DSR reset. The DOR reset is set automatically upon a pin reset. The user must manually clear this reset bit in the DOR to exit the reset state. MODE OF OPERATION PC/AT mode - (IDENT high, MFM a "don't care") The PC/AT register set is enabled, the DMA enable bit of the DOR becomes valid (IRQ and DRQ can be hi Z), and TC and DENSEL become active high signals. 25 DMA TRANSFERS DMA transfers are enabled with the Specify command and are initiated by the FDC by activating the DRQ pin during a data transfer command. The FIFO is enabled directly by asserting nDACK and addresses need not be valid. Note that if the DMA controller (i.e. 8237A) is programmed to function in verify mode, a pseudo read is performed by the FDC based only on nDACK. This mode is only available when the FDC has been configured into byte mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled, the FDC can perform the above operation by using the new Verify command; no DMA operation is needed. CONTROLLER PHASES For simplicity, command handling in the FDC can be divided into three phases: Command, Execution, and Result. Each phase is described in the following sections. Command Phase After a reset, the FDC enters the command phase and is ready to accept a command from the host. For each of the commands, a defined set of command code bytes and parameter bytes has to be written to the FDC before the command phase is complete. (Please refer to Table 18 for the command set descriptions). These bytes of data must be transferred in the order prescribed. Before writing to the FDC, the host must examine the RQM and DIO bits of the Main Status Register. RQM and DIO must be equal to "1" and "0" respectively before command bytes may be written. RQM is set false by the FDC after each write cycle until the received byte is processed. The FDC asserts RQM again to request each parameter byte of the command unless an illegal command condition is detected. After the last parameter byte is received, RQM remains "0" and the FDC automatically enters the next phase as defined by the command definition. The FIFO is disabled during the command phase to provide for the proper handling of the "Invalid Command" condition. Execution Phase All data transfers to or from the FDC occur during the execution phase, which can proceed in DMA or non-DMA mode as indicated in the Specify command. After a reset, the FIFO is disabled. Each data byte is transferred by an IRQ or DRQ depending on the DMA mode. The Configure command can enable the FIFO and set the FIFO threshold value. The following paragraphs detail the operation of the FIFO flow control. In these descriptions, 26 A low threshold value (i.e. 2) results in longer periods of time between service requests, but requires faster servicing of the request for both read and write cases. The host reads (writes) from (to) the FIFO until empty (full), then the transfer request goes inactive. The host must be very responsive to the service request. This is the desired case for use with a "fast" system. A high value of threshold (i.e. 12) is used with a "sluggish" system by affording a long latency period after a service request, but results in more frequent service requests. Non-DMA Mode - Transfers from the FIFO to the Host The IRQ pin and RQM bits in the Main Status Register are activated when the FIFO contains (16- DMA Mode - Transfers from the FIFO to the Host The FDC activates the DDRQ pin when the FIFO contains (16 - 27 If the last sector to be transferred is a partial sector, the host can stop transferring the data in mid-sector, and the FDC will continue to complete the sector as if a hardware TC was received. The only difference between these implicit functions and TC is that they return "abnormal termination" result status. Such status indications can be ignored if they were expected. Note that when the host is sending data to the FIFO of the FDC, the internal sector count will be complete when the FDC reads the last byte from its side of the FIFO. There may be a delay in the removal of the transfer request signal of up to the time taken for the FDC to read the last 16 bytes from the FIFO. The host must tolerate this delay. Result Phase The generation of IRQ determines the beginning of the result phase. For each of the commands, a defined set of result bytes has to be read from the FDC before the result phase is complete. These bytes of data must be read out for another command to start. RQM and DIO must both equal "1" before the result bytes may be read. After all the result bytes have been read, the RQM and DIO bits switch to "1" and "0" respectively, and the CB bit is cleared, indicating that the FDC is ready to accept the next command. 28 COMMAND SET/DESCRIPTIONS Commands can be written whenever the FDC is in the command phase. Each command has a unique set of needed parameters and status results. The FDC checks to see that the first byte is a valid command and, if valid, proceeds with the command. If it is invalid, an interrupt is issued. The user sends a Sense Interrupt Status command which returns an invalid command error. Refer to Table 18 or explanations of the various symbols used. Table 19 lists the required parameters and the results associated with each command that the FDC is capable of performing. SYMBOL C D D0, D1, D2, D3 DIR DS0, DS1 DTL EC EFIFO EIS EOT GAP GPL H/HDS Table 18 - Description of Command Symbols NAME DESCRIPTION Cylinder Address The currently selected address; 0 to 255. Data Pattern The pattern to be written in each sector data field during formatting. Drive Select 0-3 Designates which drives are perpendicular drives on the Perpendicular Mode Command. A "1" indicates a perpendicular drive. Direction Control If this bit is 0, then the head will step out from the spindle during a relative seek. If set to a 1, the head will step in toward the spindle. Disk Drive Select DS1 DS0 DRIVE 0 0 drive 0 0 1 drive 1 1 0 drive 2 1 1 drive 3 Special Sector By setting N to zero (00), DTL may be used to control the number of Size bytes transferred in disk read/write commands. The sector size (N = 0) is set to 128. If the actual sector (on the diskette) is larger than DTL, the remainder of the actual sector is read but is not passed to the host during read commands; during write commands, the remainder of the actual sector is written with all zero bytes. The CRC check code is calculated with the actual sector. When N is not zero, DTL has no meaning and should be set to FF HEX. Enable Count When this bit is "1" the "DTL" parameter of the Verify command becomes SC (number of sectors per track). Enable FIFO This active low bit when a 0, enables the FIFO. A "1" disables the FIFO (default). Enable Implied When set, a seek operation will be performed before executing any Seek read or write command that requires the C parameter in the command phase. A "0" disables the implied seek. End of Track The final sector number of the current track. Alters Gap 2 length when using Perpendicular Mode. Gap Length The Gap 3 size. (Gap 3 is the space between sectors excluding the VCO synchronization field). Head Address Selected head: 0 or 1 (disk side 0 or 1) as encoded in the sector ID 29 SYMBOL HLT HUT LOCK MFM MT N NCN ND OW Table 18 - Description of Command Symbols DESCRIPTION field. Head Load Time The time interval that FDC waits after loading the head and before initializing a read or write operation. Refer to the Specify command for actual delays. Head Unload Time The time interval from the end of the execution phase (of a read or write command) until the head is unloaded. Refer to the Specify command for actual delays. Lock defines whether EFIFO, FIFOTHR, and PRETRK parameters of the CONFIGURE COMMAND can be reset to their default values by a "software Reset". (A reset caused by writing to the appropriate bits of either tha DSR or DOR) MFM/FM Mode A one selects the double density (MFM) mode. A zero selects single Selector density (FM) mode. Multi-Track When set, this flag selects the multi-track operating mode. In this Selector mode, the FDC treats a complete cylinder under head 0 and 1 as a single track. The FDC operates as this expanded track started at the first sector under head 0 and ended at the last sector under head 1. With this flag set, a multitrack read or write operation will automatically continue to the first sector under head 1 when the FDC finishes operating on the last sector under head 0. Sector Size Code This specifies the number of bytes in a sector. If this parameter is "00", then the sector size is 128 bytes. The number of bytes transferred is determined by the DTL parameter. Otherwise the sector size is (2 raised to the "N'th" power) times 128. All values up to "07" hes are allowable. "07"H would equal a sector size of 16k. It is the user's resposibility to not select combinations that are not possible with the drive. N SECTOR SIZE 00 128 bytes 01 256 bytes 02 512 bytes 03 1024 bytes .. ... 07 16 Kbytes New Cylinder The desired cylinder number. Number Non-DMA Mode When set to 1, indicates that the FDC is to operate in the non-DMA Flag mode. In this mode, the host is interrupted for each data transfer. When set to 0, the FDC operates in DMA mode, interfacing to a DMA controller by means of the DRQ and DACK signals. Overwrite The bits D0-D3 of the Perpendicular Mode Command can only be NAME 30 SYMBOL PCN POLL PRETRK R RCN SC SK SRT ST0 ST1 ST2 ST3 WGATE Table 18 - Description of Command Symbols DESCRIPTION modified if OW is set to 1. OW id defined in the Lock command. Present Cylinder The current position of the head at the completion of Sense Interrupt Number Status command. Polling Disable When set, the internal polling routine is disabled. When clear, polling is enabled. Precompensation Programmable from track 00 to FFH. Start Track Number Sector Address The sector number to be read or written. In multi-sector transfers, this parameter specifies the sector number of the first sector to be read or written. Relative Cylinder Relative cylinder offset from present cylinder as used by the Relative Number Seek command. Number of Sectors The number of sectors per track to be initialized by the Format Per Track command. The number of sectors per track to be verified during a Verify command when EC is set. Skip Flag When set to 1, sectors containing a deleted data address mark will automatically be skipped during the execution of Read Data. If Read Deleted is executed, only sectors with a deleted address mark will be accessed. When set to "0", the sector is read or written the same as the read and write commands. Step Rate Interval The time interval between step pulses issued by the FDC. Programmable from 0.5 to 8 milliseconds in increments of 0.5 ms at the 1 Mbit data rate. Refer to the SPECIFY command for actual delays. Status 0 Registers within the FDC which store status information after a command has been executed. This status information is available to Status 1 the host during the result phase after command execution. Status 2 NAME Status 3 Write Gate Alters timing of WE to allow for pre-erase loads in perpendicular drives. 31 INSTRUCTION SET Table 19 - Instruction Set READ DATA DATA BUS PHASE Command R/W W W W W W W W W W Execution Result R R R R R R R ST0 ST1 ST2 C H R N Sector ID information after Command execution. D7 MT 0 D6 MFM 0 D5 SK 0 D4 0 0 D3 0 0 D2 1 D1 1 D0 0 REMARKS Command Codes Sector ID information prior to Command execution. HDS DS1 DS0 C H R N EOT GPL DTL Data transfer between the FDD and system. Status information after Command execution. 32 READ DELETED DATA DATA BUS PHASE Command R/W W W W W W W W W W Execution Result R R R R R R R ST0 ST1 ST2 C H R N Sector ID information after Command execution. D7 MT 0 D6 MFM 0 D5 SK 0 D4 0 0 D3 1 0 D2 1 D1 0 D0 0 REMARKS Command Codes Sector ID information prior to Command execution. HDS DS1 DS0 C H R N EOT GPL DTL Data transfer between the FDD and system. Status information after Command execution. 33 WRITE DATA DATA BUS PHASE Command R/W W W W W W W W W W Execution Result R R R R R R R ST0 ST1 ST2 C H R N Sector ID information after Command execution. D7 MT 0 D6 MFM 0 D5 0 0 D4 0 0 D3 0 0 D2 1 D1 0 D0 1 REMARKS Command Codes Sector ID information prior to Command execution. HDS DS1 DS0 C H R N EOT GPL DTL Data transfer between the FDD and system. Status information after Command execution. 34 WRITE DELETED DATA DATA BUS PHASE Command R/W W W W W W W W W W Execution Result R R R R R R R ST0 ST1 ST2 C H R N Sector ID information after Command execution. D7 MT 0 D6 MFM 0 D5 0 0 D4 0 0 D3 1 0 D2 0 HDS D1 0 DS1 D0 1 DS0 Sector ID information prior to Command execution. REMARKS Command Codes C H R N EOT GPL DTL Data transfer between the FDD and system. Status information after Command execution. 35 READ A TRACK DATA BUS PHASE Command R/W W W W W W W W W W Execution D7 0 0 D6 MFM 0 D5 0 0 D4 0 0 D3 0 0 D2 0 HDS D1 1 DS1 D0 0 DS0 Sector ID information prior to Command execution. REMARKS Command Codes C H R N EOT GPL DTL Data transfer between the FDD and system. FDC reads all of cylinders' contents from index hole to EOT. R R R R R R R ST0 ST1 ST2 C H R N Sector ID information after Command execution. Status information after Command execution. Result 36 VERIFY DATA BUS PHASE Command R/W W W W W W W W W W Execution Result R R R R R R R ST0 ST1 ST2 C H R N VERSION DATA BUS PHASE Command Result R/W W R D7 0 1 D6 0 0 D5 0 0 D4 1 1 D3 0 0 D2 0 0 D1 0 0 D0 0 0 REMARKS Command Code Enhanced Controller Sector ID information after Command execution. D7 MT EC D6 MFM 0 D5 SK 0 D4 1 0 D3 0 0 D2 1 HDS D1 1 DS1 D0 0 DS0 Sector ID information prior to Command execution. REMARKS Command Codes C H R N EOT GPL DTL/SC No data transfer takes place. Status information after Command execution. 37 FORMAT A TRACK DATA BUS PHASE Command R/W W W W W W W Execution for Each Sector Repeat: W W W W D7 0 0 D6 MFM 0 D5 0 0 D4 0 0 D3 1 0 D2 1 HDS D1 0 DS1 D0 1 DS0 Bytes/Sector Sectors/Cylinder Gap 3 Filler Byte Input Sector Parameters REMARKS Command Codes N SC GPL D C H R N FDC formats an entire cylinder Result R R R R R R R ST0 ST1 ST2 Undefined Undefined Undefined Undefined Status information after Command execution 38 RECALIBRATE DATA BUS PHASE Command Execution R/W W W D7 0 0 D6 0 0 D5 0 0 D4 0 0 D3 0 0 D2 1 0 D1 1 DS1 D0 1 DS0 Head retracted to Track 0 Interrupt. SENSE INTERRUPT STATUS DATA BUS PHASE Command Result R/W W R R D7 0 D6 0 D5 0 D4 0 D3 1 D2 0 D1 0 D0 0 REMARKS Command Codes Status information at the end of each seek operation. REMARKS Command Codes ST0 PCN SPECIFY DATA BUS PHASE Command R/W W W W D7 0 D6 0 D5 0 D4 0 D3 0 D2 0 D1 1 D0 1 ND REMARKS Command Codes SRT HUT HLT 39 SENSE DRIVE STATUS DATA BUS PHASE Command Result R/W W W R D7 0 0 D6 0 0 D5 0 0 D4 0 0 D3 0 0 D2 1 HDS D1 0 DS1 D0 0 DS0 Status information about FDD REMARKS Command Codes ST3 SEEK DATA BUS PHASE Command R/W W W W Execution D7 0 0 D6 0 0 D5 0 0 D4 0 0 D3 1 0 D2 1 HDS D1 1 DS1 D0 1 DS0 Head positioned over proper cylinder on diskette. CONFIGURE DATA BUS PHASE Command R/W W W W Execution W D7 0 0 0 D6 0 0 D5 0 0 D4 1 0 POLL D3 0 0 D2 0 0 D1 1 0 D0 1 0 REMARKS Configure Information REMARKS Command Codes NCN EIS EFIFO FIFOTHR PRETRK 40 RELATIVE SEEK DATA BUS PHASE Command R/W W W W D7 1 0 D6 DIR 0 D5 0 0 D4 0 0 D3 1 0 D2 1 HDS D1 1 DS1 D0 1 DS0 REMARKS RCN DUMPREG DATA BUS PHASE Command R/W W D7 0 D6 0 D5 0 D4 0 D3 1 D2 1 D1 1 D0 0 REMARKS *Note: Registers placed in FIFO Execution Result R R R R R R R R R R LOCK 0 0 PCN-Drive 0 PCN-Drive 1 PCN-Drive 2 PCN-Drive 3 SRT HLT SC/EOT D3 D2 POLL D1 D0 GAP WGATE EIS EFIFO FIFOTHR HUT ND PRETRK 41 READ ID DATA BUS PHASE Command Execution R/W W W D7 0 0 D6 MFM 0 D5 0 0 D4 0 0 D3 1 0 D2 0 HDS D1 1 DS1 D0 0 DS0 The first correct ID information on the Cylinder is stored in Data Register R ST0 Status information after Command execution. REMARKS Commands Result Disk status after the Command has completed R R R R R R ST1 ST2 C H R N 42 PERPENDICULAR MODE DATA BUS PHASE Command R/W W D7 0 OW D6 0 0 D5 0 D3 D4 1 D2 D3 0 D1 D2 0 D0 D1 1 GAP D0 0 WGATE REMARKS Command Codes INVALID CODES DATA BUS PHASE Command R/W W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS Invalid Command Codes (NoOp - fdc goes into Standby State) ST0 = 80H Invalid Codes Result R ST0 LOCK DATA BUS PHASE Command Result R/W W R D7 LOCK 0 D6 0 0 D5 0 0 D4 1 LOCK D3 0 0 D2 1 0 D1 0 0 D0 0 0 REMARKS Command Codes SC is returned if the last command that was issued was the Format command. EOT is returned if the last command was a Read or Write. NOTE: These bits are used internally only. They are not reflected in the Drive Select pins. It is the user's responsibility to maintain correspondence between these bits and the Drive Select pins (DOR). 43 DATA TRANSFER COMMANDS All of the Read Data, Write Data and Verify type commands use the same parameter bytes and return the same results information, the only difference being the coding of bits 0-4 in the first byte. An implied seek will be executed if the feature was enabled by the Configure command. This seek is completely transparent to the user. The Drive Busy bit for the drive will go active in the Main Status Register during the seek portion of the command. If the seek portion fails, it will be reflected in the results status normally returned for a Read/Write Data command. Status Register 0 (ST0) would contain the error code and C would contain the cylinder on which the seek failed. Read Data A set of nine (9) bytes is required to place the FDC in the Read Data Mode. After the Read Data command has been issued, the FDC loads the head (if it is in the unloaded state), waits the specified head settling time (defined in the Specify command), and begins reading ID Address Marks and ID fields. When the sector address read off the diskette matches with the sector address specified in the command, the FDC reads the sector's data field and transfers the data to the FIFO. After completion of the read operation from the current sector, the sector address is incremented by one and the data from the next logical sector is read and output via the FIFO. This continuous read function is called "Multi-Sector Read Operation". Upon receipt of TC, or an implied TC (FIFO overrun/underrun), the FDC stops sending data but will continue to read data from the current sector, check the CRC bytes, and at the end of the sector, terminate the Read Data Command. N determines the number of bytes per sector (see Table 22 below). If N is set to zero, the sector size is set to 128. The DTL value determines the number of bytes to be transferred. If DTL is less than 128, the FDC transfers the specified number of bytes to the host. For reads, it continues to read the entire 128-byte sector and checks for CRC errors. For writes, it completes the 128-byte sector by filling in zeros. If N is not set to 00 Hex, DTL should be set to FF Hex and has no impact on the number of bytes transferred. Table 20 - Sector Sizes N 00 01 02 03 .. 07 SECTOR SIZE 128 bytes 256 bytes 512 bytes 1024 bytes ... 16 Kbytes The amount of data which can be handled with a single command to the FDC depends upon MT (multi-track) and N (number of bytes/sector). The Multi-Track function (MT) allows the FDC to read data from both sides of the diskette. For a particular cylinder, data will be transferred starting at Sector 1, Side 0 and completing the last sector of the same track at Side 1. If the host terminates a read or write operation in the FDC, the ID information in the result phase is dependent upon the state of the MT bit and EOT byte. Refer to Table 21. 44 At the completion of the Read Data command, the head is not unloaded until after the Head Unload Time Interval (specified in the Specify command) has elapsed. If the host issues another command before the head unloads, then the head settling time may be saved between subsequent reads. If the FDC detects a pulse on the nINDEX pin twice without finding the specified sector (meaning that the diskette's index hole passes through index detect logic in the drive twice), the FDC sets the IC code in Status Register 0 to "01" indicating abnormal termination, sets the ND bit in Status Register 1 to "1" indicating a sector not found, and terminates the Read Data Command. After reading the ID and Data Fields in each sector, the FDC checks the CRC bytes. If a CRC error occurs in the ID or data field, the FDC sets the IC code in Status Register 0 to "01" indicating abnormal termination, sets the DE bit flag in Status Register 1 to "1", sets the DD bit in Status Register 2 to "1" if CRC is incorrect in the ID field, and terminates the Read Data Command. Table 22 describes the effect of the SK bit on the Read Data command execution and results. Except where noted in Table 22, the C or R value of the sector address is automatically incremented (see Table 24). MT 0 1 0 1 0 1 N 1 1 2 2 3 3 Table 21 - Effects of MT and N Bits MAXIMUM TRANSFER FINAL SECTOR READ CAPACITY FROM DISK 256 x 26 = 6,656 256 x 52 = 13,312 512 x 15 = 7,680 512 x 30 = 15,360 1024 x 8 = 8,192 1024 x 16 = 16,384 26 at side 0 or 1 26 at side 1 15 at side 0 or 1 15 at side 1 8 at side 0 or 1 16 at side 1 Table 22 - Skip Bit vs Read Data Command DATA ADDRESS RESULTS SK BIT VALUE 0 0 MARK TYPE ENCOUNTERED Normal Data Deleted Data SECTOR READ? Yes Yes CM BIT OF ST2 SET? No Yes DESCRIPTION OF RESULTS Normal termination. Address not incremented. Next sector not searched for. Normal termination. Normal termination. Sector not read ("skipped"). 1 1 Normal Data Deleted Data Yes No No Yes 45 Read Deleted Data This command is the same as the Read Data command, only it operates on sectors that contain a Deleted Data Address Mark at the beginning of a Data Field. Table 23 describes the effect of the SK bit on the Read Deleted Data command execution and results. Except where noted in Table 25, the C or R value of the sector address is automatically incremented (see Table 26). Table 23 - Skip Bit vs. Read Deleted Data Command DATA ADDRESS RESULTS SK BIT VALUE 0 MARK TYPE ENCOUNTERED Normal Data SECTOR READ? Yes CM BIT OF ST2 SET? Yes DESCRIPTION OF RESULTS Address not incremented. Next sector not searched for. Normal termination. Normal termination. Sector not read ("skipped"). Normal termination. 0 1 Deleted Data Normal Data Yes No No Yes 1 Deleted Data Yes No Read A Track This command is similar to the Read Data command except that the entire data field is read continuously from each of the sectors of a track. Immediately after encountering a pulse on the nINDEX pin, the FDC starts to read all data fields on the track as continuous blocks of data without regard to logical sector numbers. If the FDC finds an error in the ID or DATA CRC check bytes, it continues to read data from the track and sets the appropriate error bits at the end of the command. The FDC compares the ID information read from each sector with the specified value in the command and sets the ND flag of Status Register 1 to a "1" if there is no comparison. Multitrack or skip operations are not allowed with this command. The MT and SK bits (bits D7 and D5 of the first command byte respectively) should always be set to "0". This command terminates when the EOT specified number of sectors has not been read. If the FDC does not find an ID Address Mark on the diskette after the second occurrence of a pulse on the IDX pin, then it sets the IC code in Status Register 0 to "01" (abnormal termination), sets the MA bit in Status Register 1 to "1", and terminates the command. 46 MT HEAD Table 24 - Result Phase Table FINAL SECTOR TRANSFERRED TO ID INFORMATION AT RESULT PHASE HOST C H R N Less than EOT NC C+1 NC C+1 NC NC NC C+1 NC NC NC NC NC LSB NC LSB R+1 01 R+1 01 R+1 01 R+1 01 NC NC NC NC NC NC NC NC 0 0 Equal to EOT 1 Less than EOT Equal to EOT Less than EOT 0 Equal to EOT 1 Less than EOT Equal to EOT 1 NC: No Change, the same value as the one at the beginning of command execution. LSB: Least Significant Bit, the LSB of H is complemented. Write Data After the Write Data command has been issued, the FDC loads the head (if it is in the unloaded state), waits the specified head load time if unloaded (defined in the Specify command), and begins reading ID fields. When the sector address read from the diskette matches the sector address specified in the command, the FDC reads the data from the host via the FIFO and writes it to the sector's data field. After writing data into the current sector, the FDC computes the CRC value and writes it into the CRC field at the end of the sector transfer. The Sector Number stored in "R" is incremented by one, and the FDC continues writing to the next data field. The FDC continues this "Multi-Sector Write Operation". Upon receipt of a terminal count signal or if a FIFO over/under run occurs while a data field is being written, then the remainder of the data field is filled with zeros. The FDC reads the ID field of each sector and checks the CRC bytes. If it detects a CRC error in 47 one of the ID fields, it sets the IC code in Status Register 0 to "01" (abnormal termination), sets the DE bit of Status Register 1 to "1", and terminates the Write Data command. The Write Data command operates in much the same manner as the Read Data command. The following items are the same. Please refer to the Read Data Command for details: * * * * * * Transfer Capacity EN (End of Cylinder) bit ND (No Data) bit Head Load, Unload Time Interval ID information when the host terminates the command Definition of DTL when N = 0 and when N does not = 0 Write Deleted Data This command is almost the same as the Write Data command except that a Deleted Data Address Mark is written at the beginning of the Data Field instead of the normal Data Address Mark. This command is typically used to mark a bad sector containing an error on the floppy disk. Verify The Verify command is used to verify the data stored on a disk. This command acts exactly like a Read Data command except that no data is transferred to the host. Data is read from the disk and CRC is computed and checked against the previously-stored value. Because data is not transferred to the host, TC (pin 25) cannot be used to terminate this MT 0 0 0 0 1 1 1 1 EC 0 0 1 1 0 0 1 1 command. By setting the EC bit to "1", an implicit TC will be issued to the FDC. This implicit TC will occur when the SC value has decremented to 0 (an SC value of 0 will verify 256 sectors). This command can also be terminated by setting the EC bit to "0" and the EOT value equal to the final sector to be checked. If EC is set to "0", DTL/SC should be programmed to 0FFH. Refer to Table 26 and Table 27 for information concerning the values of MT and EC versus SC and EOT value. Definitions: # Sectors Per Side = Number of formatted sectors per each side of the disk. # Sectors Remaining = Number of formatted sectors left which can be read, including side 1 of the disk if MT is set to "1". Table 25 - Verify Command Result Phase Table SC/EOT VALUE TERMINATION RESULT SC = DTL Success Termination Result Phase Valid EOT # Sectors Per Side SC = DTL Unsuccessful Termination EOT > # Sectors Per Side Result Phase Invalid Successful Termination SC # Sectors Remaining AND Result Phase Valid EOT # Sectors Per Side SC > # Sectors Remaining OR Unsuccessful Termination EOT > # Sectors Per Side Result Phase Invalid SC = DTL Successful Termination Result Phase Valid EOT # Sectors Per Side SC = DTL Unsuccessful Termination EOT > # Sectors Per Side Result Phase Invalid Successful Termination SC # Sectors Remaining AND Result Phase Valid EOT # Sectors Per Side SC > # Sectors Remaining OR Unsuccessful Termination EOT > # Sectors Per Side Result Phase Invalid NOTE: If MT is set to "1" and the SC value is greater than the number of remaining formatted sectors on Side 0, verifying will continue on Side 1 of the disk. 48 Format A Track The Format command allows an entire track to be formatted. After a pulse from the IDX pin is detected, the FDC starts writing data on the disk including gaps, address marks, ID fields, and data fields per the IBM System 34 or 3740 format (MFM or FM respectively). The particular values that will be written to the gap and data field are controlled by the values programmed into N, SC, GPL, and D which are specified by the host during the command phase. The data field of the sector is filled with the data byte specified by D. The ID field for each sector is supplied by the host; that is, four data bytes per sector are needed by the FDC for C, H, R, and N (cylinder, head, sector number and sector size respectively). After formatting each sector, the host must send new values for C, H, R and N to the FDC for the next sector on the track. The R value (sector number) is the only value that must be changed by the host after each sector is formatted. This allows the disk to be formatted with nonsequential sector addresses (interleaving). This incrementing and formatting continues for the whole track until the FDC encounters a pulse on the IDX pin again and it terminates the command. Table 28 contains typical values for gap fields which are dependent upon the size of the sector and the number of sectors on each track. Actual values can vary due to drive electronics. FORMAT FIELDS SYSTEM 34 (DOUBLE DENSITY) FORMAT GAP4a 80x 4E SYNC 12x 00 IAM 3x FC C2 GAP1 SYNC 12x 50x 00 4E IDAM 3x FE A1 C Y L H D S N C GAP2 SYNC 12x 22x EOR 00 4E C C DATA AM 3x FB A1 F8 C DATA R GAP3 GAP 4b C SYSTEM 3740 (SINGLE DENSITY) FORMAT GAP4a 40x FF SYNC 6x 00 IAM FC GAP1 SYNC 26x 6x FF 00 IDAM FE C Y L H D S N C GAP2 SYNC EOR 11x 6x C C FF 00 DATA AM FB or F8 C DATA R GAP3 GAP 4b C PERPENDICULAR FORMAT GAP4a 80x 4E SYNC 12x 00 IAM 3x FC C2 GAP1 SYNC 12x 50x 00 4E IDAM 3x FE A1 C Y L H D S N C GAP2 SYNC 12x 41x EOR 00 4E C C DATA AM 3x FB A1 F8 C DATA R GAP3 GAP 4b C 49 FORMAT Table 26 - Typical Values for Formatting SECTOR SIZE N SC 128 128 512 1024 2048 4096 ... 256 256 512* 1024 2048 4096 ... 128 256 512 256 512 1024 00 00 02 03 04 05 ... 01 01 02 03 04 05 ... 0 1 2 1 2 3 12 10 08 04 02 01 12 10 09 04 02 01 0F 09 05 0F 09 05 GPL1 07 10 18 46 C8 C8 0A 20 2A 80 C8 C8 07 0F 1B 0E 1B 35 GPL2 09 19 30 87 FF FF 0C 32 50 F0 FF FF 1B 2A 3A 36 54 74 FM 5.25" Drives MFM 3.5" Drives FM MFM GPL1 = suggested GPL values in Read and Write commands to avoid splice point between data field and ID field of contiguous sections. GPL2 = suggested GPL value in Format A Track command. *PC/AT values (typical) NOTE: All values except sector size are in hex. 50 CONTROL COMMANDS Control commands differ from the other commands in that no data transfer takes place. Three commands generate an interrupt when complete: Read ID, Recalibrate, and Seek. The other control commands do not generate an interrupt. Read ID The Read ID command is used to find the present position of the recording heads. The FDC stores the values from the first ID field it is able to read into its registers. If the FDC does not find an ID address mark on the diskette after the second occurrence of a pulse on the nINDEX pin, it then sets the IC code in Status Register 0 to "01" (abnormal termination), sets the MA bit in Status Register 1 to "1", and terminates the command. The following commands will generate an interrupt upon completion. They do not return any result bytes. It is highly recommended that control commands be followed by the Sense Interrupt Status command. Otherwise, valuable interrupt status information will be lost. Recalibrate This command causes the read/write head within the FDC to retract to the track 0 position. The FDC clears the contents of the PCN counter and checks the status of the nTR0 pin from the FDD. As long as the nTR0 pin is low, the DIR pin remains 0 and step pulses are issued. When the nTR0 pin goes high, the SE bit in Status Register 0 is set to "1" and the command is terminated. If the nTR0 pin is still low after 79 step pulses have been issued, the FDC sets the SE and the EC bits of Status Register 0 to "1" and terminates the command. Disks capable of handling more than 80 tracks per side may require more than one Recalibrate command to return the head back to physical Track 0. The Recalibrate command does not have a result phase. The Sense Interrupt Status command 51 must be issued after the Recalibrate command to effectively terminate it and to provide verification of the head position (PCN). During the command phase of the recalibrate operation, the FDC is in the BUSY state, but during the execution phase it is in a NON-BUSY state. At this time, another Recalibrate command may be issued, and in this manner parallel Recalibrate operations may be done on up to four drives at once. Upon power up, the software must issue a Recalibrate command to properly initialize all drives and the controller. Seek The read/write head within the drive is moved from track to track under the control of the Seek command. The FDC compares the PCN, which is the current head position, with the NCN and performs the following operation if there is a difference: PCN < NCN: Direction signal to drive set to "1" (step in) and issues step pulses. PCN > NCN: Direction signal to drive set to "0" (step out) and issues step pulses. The rate at which step pulses are issued is controlled by SRT (Stepping Rate Time) in the Specify command. After each step pulse is issued, NCN is compared against PCN, and when NCN = PCN the SE bit in Status Register 0 is set to "1" and the command is terminated. During the command phase of the seek or recalibrate operation, the FDC is in the BUSY state, but during the execution phase it is in the NON-BUSY state. At this time, another Seek or Recalibrate command may be issued, and in this manner, parallel seek operations may be done on up to four drives at once. Note that if implied seek is not enabled, the read and write commands should be preceded by: 1) Seek command - Step to the proper track 2) Sense Interrupt Status command - Terminate the Seek command 3) Read ID - Verify head is on proper track 4) Issue Read/Write command. The Seek command does not have a result phase. Therefore, it is highly recommended that the Sense Interrupt Status command be issued after the Seek command to terminate it and to provide verification of the head position (PCN). The H bit (Head Address) in ST0 will always return to a "0". When exiting POWERDOWN mode, the FDC clears the PCN value and the status information to zero. Prior to issuing the POWERDOWN command, it is highly recommended that the user service all pending interrupts through the Sense Interrupt Status command. Sense Interrupt Status An interrupt signal on IRQ pin is generated by the FDC for one of the following reasons: 1.Upon entering the Result Phase of: a. Read Data command b. Read A Track command c. Read ID command d. Read Deleted Data command e. Write Data command f. Format A Track command g. Write Deleted Data command h. Verify command 2. End of Seek, Relative Seek, or Recalibrate command 3. FDC requires a data transfer during the execution phase in the non-DMA mode The Sense Interrupt Status command resets the interrupt signal and, via the IC code and SE bit of Status Register 0, identifies the cause of the interrupt. Table 27 - Interrupt Identification SE 0 1 1 IC 11 00 01 INTERRUPT DUE TO Polling Normal termination of Seek or Recalibrate command Abnormal termination of Seek or Recalibrate command The Seek, Relative Seek, and Recalibrate commands have no result phase. The Sense Interrupt Status command must be issued immediately after these commands to terminate them and to provide verification of the head position (PCN). The H (Head Address) bit in ST0 will always return a "0". If a Sense Interrupt Status is not issued, the drive will continue to be BUSY and may affect the operation of the next command. Sense Drive Status Sense Drive Status obtains drive status information. It has not execution phase and goes directly to the result phase from the command phase. Status Register 3 contains the drive status information. Specify The Specify command sets the initial values for each of the three internal times. The HUT (Head Unload Time) defines the time from the end of the execution phase of one of the read/write commands to the head unload state. The SRT (Step Rate Time) defines the time interval between adjacent step pulses. Note that the spacing between the first and second step pulses may be shorter than the remaining step pulses. The HLT (Head Load Time) defines the time between when the Head Load signal goes high and the read/write operation starts. The values change with the data rate speed selection and are documented in Table 28. The values are the same for MFM and FM. 52 Table 28 - Drive Control Delays (ms) HUT 2M 0 1 .. E F 64 4 .. 56 60 1M 128 8 .. 112 120 500K 256 16 .. 224 240 300K 426 26.7 .. 373 400 250K 512 32 .. 448 480 2M 4 3.75 .. 0.5 0.25 HLT 2M 00 01 02 .. 7F 7F 64 0.5 1 .. 63 63.5 1M 128 1 2 .. 126 127 500K 256 2 4 .. 252 254 300K 426 3.3 6.7 .. 420 423 1M 8 7.5 .. 1 0.5 16 15 .. 2 1 SRT 500K 300K 26.7 25 .. 3.33 1.67 250K 32 30 .. 4 2 250K 512 4 8 . 504 508 The choice of DMA or non-DMA operations is made by the ND bit. When this bit is "1", the nonDMA mode is selected, and when ND is "0", the DMA mode is selected. In DMA mode, data transfers are signalled by the FDRQ pin. NonDMA mode uses the RQM bit and the FINT pin to signal data transfers. Configure The Configure command is issued to select the special features of the FDC. A Configure command need not be issued if the default values of the FDC meet the system requirements. Configure Default Values: EIS - No Implied Seeks EFIFO - FIFO Disabled POLL - Polling Enabled FIFOTHR - FIFO Threshold Set to 1 Byte PRETRK - Pre-Compensation Set to Track 0 EIS - Enable Implied Seek. When set to "1", the FDC will perform a Seek operation before executing a read or write command. Defaults to no implied seek. EFIFO - A "1" disables the FIFO (default). This means data transfers are asked for on a byte-bybyte basis. Defaults to "1", FIFO disabled. The threshold defaults to "1". POLL - Disable polling of the drives. Defaults to "0", polling enabled. When enabled, a single interrupt is generated after a reset. No polling is performed while the drive head is loaded and the head unload delay has not expired. FIFOTHR - The FIFO threshold in the execution phase of read or write commands. This is programmable from 1 to 16 bytes. Defaults to one byte. A "00" selects one byte; "0F" selects 16 bytes. PRETRK - Pre-Compensation Start Track Number. Programmable from track 0 to 255. Defaults to track 0. A "00" selects track 0; "FF" selects track 255. 53 Version The Version command checks to see if the controller is an enhanced type or the older type (765A). A value of 90 H is returned as the result byte. Relative Seek The command is coded the same as for Seek, except for the MSB of the first byte and the DIR bit. DIR Head Step Direction Control DIR 0 1 RCN ACTION Step Head Out Step Head In increment the register). If the head was on track 40 (d), the maximum track that the FDC could position the head on using Relative Seek will be 295 (D), the initial track + 255 (D). The maximum count that the head can be moved with a single Relative Seek command is 255 (D). The internal register, PCN, will overflow as the cylinder number crosses track 255 and will contain 39 (D). The resulting PCN value is thus (RCN + PCN) mod 256. Functionally, the FDC starts counting from 0 again as the track number goes above 255 (D). It is the user's responsibility to compensate FDC functions (precompensation track number) when accessing tracks greater than 255. The FDC does not keep track that it is working in an "extended track area" (greater than 255). Any command issued will use the current PCN value except for the Recalibrate command, which only looks for the TRACK0 signal. Recalibrate will return an error if the head is farther than 79 due to its limitation of issuing a maximum of 80 step pulses. The user simply needs to issue a second Recalibrate command. The Seek command and implied seeks will function correctly within the 44 (D) track (299-255) area of the "extended track area". It is the user's responsibility not to issue a new track position that will exceed the maximum track that is present in the extended area. To return to the standard floppy range (0255) of tracks, a Relative Seek should be issued to cross the track 255 boundary. A Relative Seek can be used instead of the normal Seek, but the host is required to calculate the difference between the current head location and the new (target) head location. This may require the host to issue a Read ID command to ensure that the head is physically on the track that software assumes it to be. Different FDC commands will return different cylinder results which may be difficult to keep track of with software without the Read ID command. Perpendicular Mode The Perpendicular Mode command should be issued prior to executing Read/Write/Format commands that access a disk drive with perpendicular recording capability. With this 54 Relative Cylinder Number that determines how many tracks to step the head in or out from the current track number. The Relative Seek command differs from the Seek command in that it steps the head the absolute number of tracks specified in the command instead of making a comparison against an internal register. The Seek command is good for drives that support a maximum of 256 tracks. Relative Seeks cannot be overlapped with other Relative Seeks. Only one Relative Seek can be active at a time. Relative Seeks may be overlapped with Seeks and Recalibrates. Bit 4 of Status Register 0 (EC) will be set if Relative Seek attempts to step outward beyond Track 0. As an example, assume that a floppy drive has 300 useable tracks. The host needs to read track 300 and the head is on any track (0-255). If a Seek command is issued, the head will stop at track 255. If a Relative Seek command is issued, the FDC will move the head the specified number of tracks, regardless of the internal cylinder position register (but will command, the length of the Gap2 field and VCO enable timing can be altered to accommodate the unique requirements of these drives. Table 31 describes the effects of the WGATE and GAP bits for the Perpendicular Mode command. Upon a reset, the FDC will default to the conventional mode (WGATE = 0, GAP = 0). Selection of the 500 Kbps and 1 Mbps perpendicular modes is independent of the actual data rate selected in the Data Rate Select Register. The user must ensure that these two data rates remain consistent. The Gap2 and VCO timing requirements for perpendicular recording type drives are dictated by the design of the read/write head. In the design of this head, a pre-erase head precedes the normal read/write head by a distance of 200 micrometers. This works out to about 38 bytes at a 1 Mbps recording density. Whenever the write head is enabled by the Write Gate signal, the pre-erase head is also activated at the same time. Thus, when the write head is initially turned on, flux transitions recorded on the media for the first 38 bytes will not be preconditioned with the pre-erase head since it has not yet been activated. To accommodate this head activation and deactivation time, the Gap2 field is expanded to a length of 41 bytes. The format field shown on page 61 illustrates the change in the Gap2 field size for the perpendicular format. On the read back by the FDC, the controller must begin synchronization at the beginning of the sync field. For the conventional mode, the internal PLL VCO is enabled (VCOEN) approximately 24 bytes from the start of the Gap2 field. But, when the controller operates in the 1 Mbps perpendicular mode (WGATE = 1, GAP = 1), VCOEN goes active after 43 bytes to accommodate the increased Gap2 field size. For both cases, and approximate two-byte cushion is maintained from the beginning of the sync field for the purposes of avoiding write splices in the presence of motor speed variation. For the Write Data case, the FDC activates Write Gate at the beginning of the sync field under the conventional mode. The controller then writes a new sync field, data address mark, data field, and CRC as shown in Figure 4. With the pre-erase head of the perpendicular drive, the write head must be activated in the Gap2 field to insure a proper write of the new sync field. For the 1 Mbps perpendicular mode (WGATE = 1, GAP = 1), 38 bytes will be written in the Gap2 space. Since the bit density is proportional to the data rate, 19 bytes will be written in the Gap2 field for the 500 Kbps perpendicular mode (WGATE = 1, GAP =0). It should be noted that none of the alterations in Gap2 size, VCO timing, or Write Gate timing affect normal program flow. The information provided here is just for background purposes and is not needed for normal operation. Once the Perpendicular Mode command is invoked, FDC software behavior from the user standpoint is unchanged. The perpendicular mode command is enhanced to allow specific drives to be designated Perpendicular recording drives. This enhancement allows data transfers between Conventional and Perpendicular drives without having to issue Perpendicular mode commands between the accesses of the different drive types, nor having to change write pre-compensation values. 55 When both GAP and WGATE bits of the PERPENDICULAR MODE COMMAND are both programmed to "0" (Conventional mode), then D0, D1, D2, D3, and D4 can be programmed independently to "1" for that drive to be set automatically to Perpendicular mode. In this mode the following set of conditions also apply: 1. The GAP2 written to a perpendicular drive during a write operation will depend upon the programmed data rate. 2. The write pre-compensation given to a perpendicular mode drive wil be 0ns. 3. For D0-D3 programmed to "0" for conventional mode drives any data written will be at the currently programmed write pre-compensation. Note: Bits D0-D3 can only be overwritten when OW is programmed as a "1". If either GAP or WGATE is a "1" then D0-D3 are ignored. Software and hardware resets have the following effect on the PERPENDICULAR MODE COMMAND: 1. "Software" resets (via the DOR or DSR registers) will only clear GAP and WGATE bits to "0". D0-D3 are unaffected and retain their previous value. 2. "Hardware" resets will clear all bits ( GAP, WGATE and D0-D3) to "0", i.e all conventional mode. WGATE 0 0 1 1 GAP 0 1 0 1 Table 29 - Effects of WGATE and GAP Bits LENGTH OF PORTION OF GAP 2 GAP2 FORMAT WRITTEN BY WRITE MODE FIELD DATA OPERATION Conventional Perpendicular (500 Kbps) Reserved (Conventional) Perpendicular (1 Mbps) 22 Bytes 22 Bytes 22 Bytes 41 Bytes 0 Bytes 19 Bytes 0 Bytes 38 Bytes 56 LOCK In order to protect systems with long DMA latencies against older application software that can disable the FIFO the LOCK Command has been added. This command should only be used by the FDC routines, and application software should refrain from using it. If an application calls for the FIFO to be disabled then the CONFIGURE command should be used. The LOCK command defines whether the EFIFO, FIFOTHR, and PRETRK parameters of the CONFIGURE command can be RESET by the DOR and DSR registers. When the LOCK bit is set to logic "1" all subsequent "software RESETS by the DOR and DSR registers will not change the previously set parameters to their default values. All "hardware" RESET from the RESET pin will set the LOCK bit to logic "0" and return the EFIFO, FIFOTHR, and PRETRK to their default values. A status byte is returned immediately after issuing a a LOCK command. This byte reflects the value of the LOCK bit set by the command byte. ENHANCED DUMPREG The DUMPREG command is designed to support system run-time diagnostics and application software development and debug. To accommodate the LOCK command and the enhanced PERPENDICULAR MODE command the eighth byte of the DUMPREG command has been modified to contain the additional data from these two commands. COMPATIBILITY The FDC37C78 was designed with software compatibility in mind. It is a fully backwardscompatible solution with the older generation 765A/B disk controllers. The FDC also implements on-board registers for compatibility with PC/AT and PC/XT floppy disk controller subsystems. After a hardware reset of the FDC, all registers, functions and enhancements default to a PC/AT compatible operating mode. 57 AUTO POWER MANAGEMENT Power management capabilities are provided for the floppy disk. Two types of power management are provided; direct powerdown and auto powerdown. Direct powerdown is controlled by the powerdown bit in the configuration registers. Auto Powerdown can be enabled by setting the Auto Powerdown Enable bit in the configluation registers. FDC Power Management Direct power management is controlled by bit 3 of Configuration Register 0(CR0). Refer to CR0 bit 3 for more information. Auto Power Management is enabled by CR7 bit 7. When set, this bit allows FDC to enter powerdown when all of the following conditions have been met: 1. 2. The motor enable pins of register DOR are inactive (zero). The part must be idle; MSR=80H and INT = 0 (INT may be high even if MSR = 80H due to polling interrupts). The internal head unload timer must have expired. The Auto powerdown timer (10msec) must have timed out. 2. An internal timer is initiated as soon as the auto powerdown command is enabled. The part is then powered down when all the conditions are met. During the countdown of the powerdown timer, any operation of read MSR or read/write data (FIFO) will reinitiate the timer. 3. Disabling the auto powerdown mode cancels the timer and holds the FDC37C78 out of auto powerdown. DSR From Powerdown If DSR powerdown is used when the part is in auto powerdown, the DSR powerdown will override the auto powerdown. However, when the part is awakened from DSR powerdown, the auto powerdown will once again become effective. Wake Up From Auto Powerdown If the part enters the powerdown state through the auto powerdown mode, then the part can be awakened by reset or by appropriate access to certain registers. If a hardware or software reset is used then the part will go through the normal reset sequence. If the access is through the selected registers, then the FDC37C78 resumes operation as though it was never in powerdown. Besides activating the RESET pin or one of the software reset bits in the DOR or DSR, the following register accesses will wake up the part: 1. Enabling any one of the motor enable bits in the DOR register (reading the DOR does not awaken the part). A read from the MSR register. A read or write to the Data register. 3. 4. 58 Once awake, the FDC37C78 will reinitiate the auto powerdown timer for 10 ms. The part will powerdown again when all the powerdown conditions are satisfied. Register Behavior Table 30 reiterates the AT registers available. It also shows the type of access permitted. In order to maintain software transparency, access to all the registers must be maintained. As Table 30 shows, two sets of registers are distinguished based on whether their access results in the part remaining in powerdown state or exiting it. Access to all other registers is possible without awakening the part. These registers can be accessed during powerdown without changing the status of the part. A read from these registers will reflect the true status as shown in the register description in the FDC description. A write to the part will result in the part retaining the data and subsequently reflecting it when the part awakens. Accessing the part during powerdown may cause an increase in the power consumption by the part. The part will revert back to its low power mode when the access has been completed. Pin Behavior The FDC37C78 is specifically designed for portable PC systems in which power conservation is a primary concern. This makes the behavior of the pins during powerdown very important. The pins of the FDC37C78 can be divided into two major categories: system interface and floppy disk drive interface. The floppy disk drive pins are disabled so that no power will be drawn through the part as a result of any voltage applied to the pin within the part's power supply range. Most of the system interface pins are left active to monitor system accesses that may wake up the part. System Interface Pins Table 31 gives the state of the system interface pins in the powerdown state. Pins unaffected by the powerdown are labeled "Unchanged". Input pins are "Disabled" to prevent them from causing currents internal to the FDC37C78 when they have indeterminate input values. 59 Table 30 - PC/AT Available Registers Available Registers Base + Address 00H 01H 02H 03H 04H 06H 07H 07H 04H 05H PC-AT ------DOR (1) --DSR (1) --DIR CCR Access to these registers wakes up the part MSR Data R R/W Access Permitted R R R/W --W --R W Access to these registers DOES NOT wake up the part Note 1: Writing to the DOR or DSR does not wake up the part, however, writing any of the motor enable bits or doing a software reset (via DOR or DSR reset bits) will wake up the part Table 31 - State of System Pins in Auto Powerdown System Pins State in Auto Powerdown Input Pins IOR IOW A[0:9] D[0:7] RESET IDENT DACK TC IRQ DB[0:7] FDRQ Unchanged Unchanged Unchanged Unchanged Unchanged Unchanged Unchanged Unchanged Output Pins Unchanged (low) Unchanged Unchanged (low) 60 FDD Interface Pins All pins in the FDD interface which can be connected directly to the floppy disk drive itself are either DISABLED or TRISTATED. Pins used for local logic control or part programming are unaffected. Table 32 depicts the state of the floppy disk drive interface pins in the powerdown state. Table 32 - State of Floppy Disk Drive Interface Pins in Powerdown FDD Pins State in Auto Powerdown Input Pins RDATA WP TRK0 INDX DRV2 DSKCHG Output Pins MOTEN[0:3] DS[0:3] DIR STEP WRDATA WE HDSEL DENSEL DRATE[0:1] Tristated Tristated Active Active Tristated Tristated Active Active Active Input Input Input Input Input Input 61 CONFIGURATION The configuration of the chip is programmable through software selectable configuration registers. CONFIGURATION REGISTER ADDRESS The Configuration Registers are located at address offset +0 and +1 with nCS active. CONFIGURATION REGISTERS Configuration Mode The configuration registers are used to select programmable options of the chip. After power up, the chip is in the default mode. The default modes are identified in the Configuration Mode Register Description. To program the configuration registers, the following sequence must be followed: 1. 2. 3. Enter Configuration Mode. Configure the Configuration Registers. Exit Configuration Mode. The chip contains configuration registers CR00CR1F. These registers are accessed by first writing the number (0-1FH) of the desired register to port +0 and then writing or reading the configuration register through port +1. Exit Configuration Mode The configuration mode is exited by writing an AAH to port +0. Programming Example The following is an example of a configuration program in Intel 8086 assembly language and assumes that the base address is set to 3F0H. Enter Configuration Mode To enter the configuration mode, two writes in succession to port +0 with 55H data are required. If a write to another address or port occurs between these two writes, the chip does not enter the configuration mode. It is strongly recommended that interrupts be disabled for the duration of these two writes. 62 ;-----------------------------. ; ENTER CONFIGURATION MODE | ;-----------------------------' MOV DX,3F0H MOV AX,055H ; CLI ; disable interrupts OUT DX,AL OUT DX,AL STI ; enable interrupts ;-----------------------------. ; CONFIGURE REGISTERS CR0-CRx | ;-----------------------------' MOV DX,3F0H MOV AL,00H OUT DX,AL ; Point to CR0 MOV DX,3F1H MOV AL,3FH OUT DX,AL ; Update CR0 ; MOV DX,3F0H ; MOV AL,01H OUT DX,AL ; Point to CR1 MOV DX,3F1H MOV AL,9FH OUT DX,AL ; Update CR1 ; ; Repeat for all CRx registers ; ;-----------------------------. ; EXIT CONFIGURATION MODE | ;-----------------------------' MOV DX,3F0H MOV AX,0AAH OUT DX,AL 63 Table 33 - Configuration Registers Default 28H 90H 00H 70H 00H 00H FFH 00H 00H 00H 00H 00H 00H 78H 00H 00H 00H 00H 00H 00H CR00 CR01 CR02 CR03 CR04 CR05 CR06 CR07 CR08 CR09 CR0A CR0B CR0C CR0D CR0E CR0F CR10 CR11 CR12CR1E CR1F FDD3-DTx FDD2-DTx Test Test Test Test Test Test Test Test Test Test Test Test FDD3-DRTx Reserved Reserved EXTx4 DRV 0X1 Floppy Drive C DB7 Valid Lock CRx Reserved Reserved IDENT DB6 Reserved DB5 OSC Reserved Reserved MFM DRVDEN 1 DB4 Reserved DB3 FDC PWR Reserved Reserved Reserved Reserved DEN SEL DMA Mode Floppy Drive B Media ID Polarity Reserved Reserved Reserved FDD2-DRTx Reserved Device ID/ 78H Device Revision/00 Test Test Test Reserved FDD1-DTx FDD0-DTx Test Test Test Test Test Test Test Test Test FDD1-DRTx Reserved Reserved Reserved Reserved FDD0-DRTx Reserved Floppy Drive A Floppy Boot Drive Reserved Reserved Reserved Reserved Reserved DB2 PDEN Reserved Reserved Enhanced FDC Mode 2 Reserved DB1 Reserved Reserved DB0 Floppy Drive D Auto Power Management Reserved Reserved Reserved Configuration Register Description The configuration registers consist of the Configuration Select Register (CSR) and Configuration Registers CR00 - CR1F. The configuration select register is written to by writing to port +0. The Configuration Registers CR00; CR1F are accessed by reading or writing to port +1. Configuration Select Register (CSR) This register can only be accessed when the chip is in the Configuration Mode. This register, located at port +0, must be initialized upon entering the Configuration Mode before the configuration registers can be accessed and is used to select which of the Configuration Registers are to be accessed at port +1. Configuration Registers CR00 -CR1F These registers are set to their default values at power up and are not affected by RESET (except where explicitly defined that a hardware reset causes that bit to be reset to default). They are accessed at port +1. Refer to the following descriptions for the function of each configuration register. 64 CR00 This register can only be accessed when the chip is in the Configuration Mode and after the CSR has been initialized to 00H. The default value of this register after power up is 28H. Table 34 - CR00 BIT NO. 0:1 2 BIT NAME Reserved PDEN Read only. Read as 0 Power Down and Idle enable. 0 nDS1pin=nDS1, nMTR1pin=nMTR1 1 nDS1pin=Power Down, nMTR1pin=Idle 3 4, 6 5 FDC Power Reserved OSC A high level on this bit, supplies power to the FDC (default). A low level on this bit puts the FDC in low power mode. Read only. A read returns bits 4 and 6 as a 0. Oscillator Control. 0 = Oscillator OFF 1 = Oscillator ON (default) A high level on this software controlled bit can be used to indicate that a valid configuration cycle has occurred. The control software must take care to set this bit at the appropriate times. Set to zero after power up. This bit has no effect on any other hardware in the chip. DESCRIPTION 7 Valid CR01 This register can only be accessed in the Configuration Mode and initialized to 01H. The default value of this register after power up is 90H. Table 35 - CR01 BIT NO. 0,1,2,3 4 5,6 7 BIT NAME Reserved Reserved Reserved Lock CRx DESCRIPTION Read Only. A read returns a 0. Read Only. A read returns a 1. Read Only. A read returns a 0. after the CSR has been A high level on this bit enables the reading and writing of CRxx registers (Default). A low level on this bit disables the reading and writing of all CRxx registers. Once set to 0, this bit can only be set to 1 by a hard reset or power-up reset. 65 CR02 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 02H. The default value of this register after power up is 00H. Table 36 - CR02 BIT NO. 0:7 BIT NAME Reserved DESCRIPTION Read Only. A read returns a 0. CR03 This register can only be accessed in the Configuration Mode and the CSR has been initialized to 03H. The default value after power up is 70H. Table 37 - CR03 DESCRIPTION Reserved - Read as zero Bit 1 Floppy Mode - Refer to the description of the TAPE DRIVE REGISTER (TDR) for more information on these modes. NORMAL Floppy Mode (Default) Enhanced Floppy Mode 2 (OS2) BIT NO. 0 1 BIT NAME Reserved Enhanced Floppy Mode 2 0 1 2 3 4 5 6 Reserved Reserved DRVDEN1 MFM IDENT Reserved - Read as zero Reserved - Read as zero 0 1 DRVDEN 1 output as per DRVDEN table DRVDEN 1 pin is tri-state (default) IDENT is used in conjunction with MFM to define the interface mode of operation. IDENT 1 1 0 0 Reserved - Read as zero MFM 1 0 1 0 MODE AT Mode (Default) Reserved Reserved Reserved 7 Reserved CR04 This register can only be accessed in the Configuration Mode and the CSR has been initialized to 04H. The default value after power up is 00H. Table 38 - CR04 BIT NO. 0:7 BIT NAME Reserved Reserved - Read as zero 66 DESCRIPTION CR05 This register can only be accessed in the Configuration Mode and the CSR has been initialized to 05H. The default value after power up is 00H. Table 39 - CR05- Floppy Disk Extended Setup Register BIT NAME DESCRIPTION Reserved FDC DMA Mode Read Only. A read returns a 0. 0=(default) Burst mode is enabled for the FDC FIFO execution phase data transfers. 1=Non-Burst mode enabled. The FDRQ and FIRQ pins are strobed once for each byte transferred while the FIFO is enabled. Bit 4 0 0 1 1 5 6 7 Swap Drv 0,1 EXTx4 Reserved Bit 3 0 1 0 1 Densel output Normal (Default) Reserved 1 0 BIT NO. 0,1 2 4,3 DenSel A high level on this bit, swaps drives and motor sel 0 and 1 of the FDC. A low level on this bit does not (Default). External 4 drive support: 0=Internal 2 drive decoder (default). 1=External 4 drive decoder (External 2 to 4 decoder required). Read Only. A read of this bit returns a 0 CR06 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 06H. The default value of this register after power up is FFH. This register holds the floppy disk drive types for up to four floppy disk drives. CR07 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 07H. The default value of this register after power up is 00H. This register holds the value for the auto power management, polarity of the media ID bits and floppy boot drive information. 67 Table 40 - CR07 BIT NO. 0,1 BIT NAME Floppy Boot DESCRIPTION This bit is used to define the boot floppy. 0 = Drive A (default) 1 = Drive B 0 = Non-invert 1 = Invert 0 = Non-invert 1 = Invert Read as 0. This bit controls the AUTOPOWER DOWN feature of the Floppy Disk. The function is: 0 = Auto powerdown disabled (default) 1 = Auto powerdown enabled This bit is reset to the default state by POR or a hardware reset. 2 3 4:6 7 Media ID0 Polarity Media ID1 Polarity Reserved Floppy Disk Enable CR08 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 08H. The default value of this register after power up is 00H. This register is read only. CR09 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 09H. The default value of this register after power up is 00H. This register is read only. CR0A This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 0AH. The default value of this register after power up is 00H. This register is read only. CR0B This register can only be ac1cessed in the Configuration Mode and after the CSR has been initialized to 0BH. The default value of this register after power up is 00H. This register indicates the data rate table used for each drive. Refer to CR1F for Drive Type register. Table 41 - CR0B FDD3 D7 DRT1 D6 DRT0 D5 DRT1 FDD2 D4 DRT0 D3 DRT1 FDD1 D2 DRT0 D1 DRT1 FDD0 D0 DRT0 CR0C This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 0CH. The default value of this register after power up is 00H. This register is reserved. 68 CR0D This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 0DH. This register is read only. This is the Device ID. The default value of this register after power up is 78H. CR0E This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 0EH. This register is read only. The default value of this register after power up is 00H. This is used to identify the chip revision level. CR0F This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 0FH. The default value of this register after power up is 00H. This is a test register and must be left as 00H. Table 42 - CR0F BIT NO. 0:7 BIT NAME Reserved DESCRIPTION Reserved For Test CR10 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 10H. The default value of this register after power up is 00H. This is a test register and must be left as 00H. Table 43 - CR10 BIT NO. 0:7 BIT NAME Reserved DESCRIPTION Reserved For Test CR11 This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 11H. The default value of this register after power up is 00H. This is a test register and must be left as 00H. Table 44 - CR11 BIT NO. 0:7 BIT NAME Reserved DESCRIPTION Reserved For Test CR12-CR1E These registers are reserved. The default value of these registers after power up is 00H. 69 CR1F This register can only be accessed in the Configuration Mode and after the CSR has been initialized to 1FH. The default value of this register after power up is 00H. This register indicates the Drive Type used for each drive. Refer to CR0B for Data Rate Table register. FDD3 D7 DT0 D6 DT1 D5 DT0 FDD2 D4 DT1 D3 DT0 FDD1 D2 DT1 D1 DT0 FDD0 D0 DT1 DTx = Drive Type select DT0 0 0 DT1 DRVDEN0 (Note) DENSEL DRVDEN1 (Note) DRATE0 Drive Type 4/2/1 MB 3.5" 2/1 MB 5.25" FDDS 2/1.6/1 MB 3.5" (3-MODE) 0 1 1 Note: 1 0 1 DRATE1 nDENSEL DRATE0 DRATE0 DRATE0 DRATE1 DENSEL, DRATE1 and DRATE0 map onto two output pins DRVDEN0 and DRVDEN1. 70 OPERATIONAL DESCRIPTION MAXIMUM GUARANTEED RATINGS* Operating Temperature Range ..............................................................................................0oC to +70oC Storage Temperature Range .............................................................................................. -55o to +150oC Lead Temperature Range (soldering, 10 seconds).........................................................................+325oC Positive Voltage on any pin, with respect to Ground .................................................................... VIO+0.3V Negative Voltage on any pin, with respect to Ground ........................................................................ -0.3V Maximum VIO ....................................................................................................................................... +7V Maximum VCC ........................................................................................................................................VIO *Stresses above those listed above could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other condition above those indicated in the operation sections of this specification is not implied. Note: When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. If this possibility exists, it is suggested that a clamp circuit be used. DC ELECTRICAL CHARACTERISTICS (TA = 0C - 70C, Vcc = +3.3 V 10%) PARAMETER SYMBOL MIN TYP MAX UNITS I Type Input Buffer Low Input Level High Input Level IS Type Input Buffer Low Input Level High Input Level Schmitt Trigger Hysteresis ICLK Input Buffer Low Input Level High Input Level Input Leakage Low Input Leakage High Input Leakage IIL IIH -10 -10 71 +10 +10 A A VIN = 0 VIN = VIO VILCK VIHCK 2.2 0.4 V V VILIS VIHIS VHYS 2.2 250 0.8 V V mV Schmitt Trigger Schmitt Trigger VILI VIHI 2.0 0.8 V V TTL Levels COMMENTS PARAMETER I/O12 Type Buffer Low Output Level High Output Level Output Leakage O12 Type Buffer Low Output Level High Output Level Output Leakage OD20 Type Buffer Low Output Level Output Leakage Supply Current Active Supply Current Standby SYMBOL MIN TYP MAX UNITS COMMENTS VOL VOH IOL 2.4 -10 0.5 V V IOL = 12 mA IOH = -6 mA VIN = 0 to VIO (Note 1) +10 A VOL VOH IOL 2.4 -10 0.5 V V IOL = 12 mA IOH = -6 mA VIN = 0 to VIO (Note 1) +10 A VOL IOH ICC ICSBY -10 0.5 +10 TBD TBD V A mA mA IOL = 20 mA VOH = 0 to VIO (Note 2) All outputs open. (Note 3) Note 1: All output leakages are measured with the current pins in high impedance. Note 2: Output leakage is measured with the low driving output off. Note 3: Defined by the device configuration. DC ELECTRICAL CHARACTERISTICS (TA = 0C - 70C, Vcc = +5 V 10%) PARAMETER SYMBOL MIN TYP MAX UNITS I Type Input Buffer Low Input Level High Input Level IS Type Input Buffer Low Input Level High Input Level Schmitt Trigger Hysteresis VILIS VIHIS VHYS 2.2 250 0.8 V V mV Schmitt Trigger Schmitt Trigger VILI VIHI 2.0 0.8 V V TTL Levels COMMENTS 72 PARAMETER ICLK Input Buffer Low Input Level High Input Level Input Leakage Low Input Leakage High Input Leakage I/O12 Type Buffer Low Output Level High Output Level Output Leakage O12 Type Buffer Low Output Level High Output Level Output Leakage OD20 Type Buffer Low Output Level Output Leakage Supply Current Active Supply Current Standby SYMBOL MIN TYP MAX UNITS COMMENTS VILCK VIHCK 3.0 0.4 V V IIL IIH -10 -10 +10 +10 A A VIN = 0 VIN = VIO VOL VOH IOL 2.4 -10 0.5 V V IOL = 24 mA IOH = -12mA VIN = 0 to VIO (Note 1) +10 A VOL VOH IOL 2.4 -10 0.5 V V IOL = 24 mA IOH = -12 mA VIN = 0 to VIO (Note 1) +10 A VOL IOH ICC ICSBY -10 0.5 +10 TBD TBD V A mA mA IOL = 48 mA VOH = 0 to VIO (Note 2) All outputs open. (Note 3) Note 1: All output leakages are measured with the current pins in high impedance. Note 2: Output leakage is measured with the low driving output off. Note 3: Defined by the device configuration. CAPACITANCE TA = 25C; fc = 1MHz; VCC = 3.3V, 5V LIMITS PARAMETER Clock Input Capacitance Input Capacitance SYMBOL CIN CIN 73 MIN TYP MAX 20 10 UNIT pF pF TEST CONDITION All pins except pin under test tied to Output Capacitance COUT 20 pF AC ground 74 TIMING DIAGRAMS t3 nCS t1 t2 nIOR t4 DATA (D0-D7) DATA VALID t5 BUSY t6 IRQ Parameter t1 t2 t3 t4 t5 t6 nCS Set Up to nIOR Low nIOR Width nCS Hold from nIOR High Data Access Time from nIOR Low Data to Float Delay from nIOR High Read Strobe to Clear IRQ min 40 150 10 typ max units ns ns ns 100 10 40 60 55 ns ns ns FIGURE 3 - MICROPROCESSOR READ TIMING 75 t3 nCS t2 t1 nIOW t4 t5 DATA (D0-D7) DATA VALID t6 IRQ Parameter t1 t2 t3 t4 t5 t6 nCS Set Up to nIOW Low nIOW Width nCS Hold from nIOW High Data Set Up Time to nIOW High Data Hold Time from nIOW High Write Strobe to Clear IRQ min 40 150 10 40 10 typ max units ns ns ns ns ns 40 55 ns FIGURE 4 - MICROPROCESSOR WRITE TIMING 76 t15 nCS t16 t3 t2 DRQ, t1 t4 nDACK t14 t11 t6 nIOR or nIOW t5 t8 t12 t10 t7 DATA (DO-D7) t13 TC DATA VALID t9 Parameter t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 nDACK Delay Time from DRQ High DRQ Reset Delay from nIOR or nIOW DRQ Reset Delay from nDACK Low nDACK Width nIOR Delay from DRQ High nIOW Delay from DRQ High Data Access Time from nIOR Low Data Set Up Time to nIOW High Data to Float Delay from nIOR High Data Hold Time from nIOW High nDACK Set Up to nIOW/nIOR Low nDACK Hold After nIOW/nIOR High TC Pulse Width nCS Set Up to nIOR/nIOW nCS Hold from nDACK TC Active to DRQ Inactive min 0 typ max 100 100 units ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 150 0 0 40 10 10 5 10 60 40 10 100 60 100 FIGURE 5 - DMA TIMING 77 t1 t2 X1 t4 nRESET t2 Name t1 t2 Description Clock CycleTime for 24MHZ Clock High Time/Low Time for 14.318MHZ Clock Rise Time/Fall Time (not shown) min 40 14 typ max 43.33 Units ns ns 5 1.5 ns us t6 nRESET Low Time NOTE 1: The nRESET low time is dependent upon the processor clock. The nRESET must be active for a minimum of 24 x16MHz clock cycles. FIGURE 6 - CLOCK TIMING 78 t3 nDIR t4 t1 nSTEP t2 t5 nDS0-1 t6 nINDEX t7 nRDATA t8 nWDATA nIOW t9 nDS0-1, nMTR0-1 t9 Parameter t1 t2 t3 t4 t5 t6 t7 t8 t9 nDIR Set Up to nSTEP Low nSTEP Active Time Low nDIR Hold Time After nSTEP nSTEP Cycle Time nDS0-1 Hold Time from nSTEP Low nINDEX Pulse Width nRDATA Active Time Low nWDATA Write Data Width Low nDS0-1, MTR0-1 from End of nIOW min typ 4 24 96 132 20 2 40 .5 25 max units X* X* X* X* X* X* ns Y* ns *X specifies one MCLK period and Y specifies one WCLK period. MCLK = Controller Clock to FDC (See Table 6). WCLK = 2 x Data Rate (See Table 6). FIGURE 7 - DISK DRIVE TIMING 79 FIGURE 8 - 48 PIN TQFP PACKAGE DIMENSIONS MIN ~ 0.05 1.35 8.80 4.40 6.90 8.80 4.40 6.90 0.09 0.45 ~ 0 0.17 0.08 0.08 o A A1 A2 D D/2 D1 E E/2 E1 H L L1 e W R1 R2 NOMINAL ~ 0.10 1.40 9.00 4.50 7.00 9.00 4.50 7.00 ~ 0.60 1.00 0.50 Basic ~ ~ ~ ~ MAX 1.6 0.15 1.45 9.20 4.60 7.10 9.10 4.60 7.10 0.20 0.75 ~ 7o 0.27 ~ 0.20 80 REMARK Overall Package Height Standoff Body Thickness X Span 1 /2 X Span Measure from Centerline X body Size Y Span 1 /2 Y Span Measure from Centerline Y body Size Lead Frame Thickness Lead Foot Length from Centerline Lead Length Lead Pitch Lead Foot Angle Lead Width Lead Shoulder Radius Lead Foot Radius ccc ccc MIN ~ ~ NOMINAL ~ ~ MAX 0.0762 0.08 REMARK Coplanarity (Assemblers) Coplanarity (Test House) Note 1: Controlling Unit: millimeter Note 2: Tolerance on the position of the leads is 0.04 mm maximum. Note 3: Package body dimensions D1 and E1 do not include the mold protrusion. Maximum mold protrusion is 0.25 mm. Note 4: Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane is 0.781.08 mm. Note 5: Details of pin 1 identifier are optional but must be located within the zone indicated. 81 FDC37C78 ERRATA SHEET PAGE 80 SECTION/FIGURE/ENTRY FIGURE 8/Table CORRECTION See Italicized Text DATE REVISED 06/07/99 80 Arkay Drive Hauppauge, NY 11788 (631) 435-6000 FAX (631) 273-3123 Copyright (c) SMSC 2004. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. FDC37C78 Rev. 03/27/2000 |
Price & Availability of FDC37C78
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |